Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model) › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0370842 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  B1476  A/C Inverter Load System Malfunction  


DESCRIPTION

The operation of the compressor with motor assembly is stopped and this DTC is stored if the rotation load is too large or too small while the compressor with motor assembly is operating.

Possible causes are refrigerant leaks, overcharged refrigerant, insufficient cooling due to a condenser fan circuit malfunction, or compressor lock.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1476 A/C Inverter Load System Malfunction
·

Diagnosis condition: Compressor operation request

·

Malfunction status: Motor rotation load while the compressor is operating is too large or too small

·

Detection time: None


·

Refrigerant volume

·

Compressor with motor assembly

·

Cooling fan system

·

CAN communication system


Memorized

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test.


e.

Check the operation by referring to the table below.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Restrict Condition
Control the Engine Cooling Fan Duty Ratio Electric cooling fan motor operation 0 to 100 (%) Perform this test when vehicle is stopped.
Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11
OK:

Electric cooling fan operates smoothly.



Result:
Proceed to
OK
NG



OK

3.CHECK REFRIGERANT PRESSURE

NG

3.CHECK REFRIGERANT PRESSURE

b.

Turn the power switch on (READY).


c.

Read the manifold gauge pressure when the following conditions are met.

i.

Prepare the vehicle according to the table below.

Measurement Condition:
Item Condition
Vehicle Condition Power switch on (READY)
Doors Fully closed (windows also fully closed)
A/C Switch On
Recirculation/fresh Control Switch Recirculation
Set Temperature MAX COLD
Blower Speed HI
Air Conditioning Air Inlet Temperature 25 to 35°C (77 to 95°F)



Standard Pressure:
Low pressure side:

150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)

High pressure side:

1370 to 1570 kPa (14 to 16 kgf/cm2, 199 to 228 psi)


Result:
Proceed to
OK
NG



OK

NG