The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the compressor with motor assembly removal/installation are shown below.
Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Use the same procedure as for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
G3834
2.REMOVE SERVICE PLUG GRIP
3.CHECK TERMINAL VOLTAGE
Disconnect the engine room main wire.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FRAME WIRE>REMOVAL
Remove the connector cover assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER (for 2WD)>REMOVAL
Check the terminal voltage.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER (for 2WD)>REMOVAL
Install the connector cover assembly.
Connect the engine room main wire.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>FRAME WIRE>INSTALLATION
4.REMOVE FRONT WHEEL RH
75601A
5.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH
Use the same procedure described as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>WHEEL OPENING MOULDING (for Front)>REMOVAL
53896B
6.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
53895B
7.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
51441
8.REMOVE NO. 1 ENGINE UNDER COVER
76621D
9.REMOVE FRONT FENDER MUDGUARD RH (w/ Mudguard)
Use the same procedure described as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>MUDGUARD>REMOVAL
53736E
10.REMOVE FRONT FENDER APRON SEAL RH
53875A
11.REMOVE FRONT FENDER LINER RH
88704
12.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
Remove the bolt and disconnect the suction hose sub-assembly.
Do not apply excessive force to the suction hose sub-assembly.
Remove the O-ring from the suction hose sub-assembly.
Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.
88711
13.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose.
Do not apply excessive force to the No. 1 cooler refrigerant discharge hose.
Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.
88370
14.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY
|
Connector (A) |
Disconnect the connector (A).
Remove the 2 nuts.
|
Bolt |
|
Stud Bolt |
Using an E8 "TORX" socket wrench, remove the 2 stud bolts and bolt.
Do not drop or subject the parts to any impact.
|
Connector (B) |
|
Slide |
|
Green-colored Lock |
Slide the green-colored lock of the connector (B) as shown in the illustration to release it and disconnect the connector.
Make sure to wear insulated gloves.
Insulate the disconnected terminals and connector with insulating tape.
Remove the compressor with motor assembly from the location shown in the illustration.
Do not damage surrounding parts.