Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › 2018.10–2019.02
RM3620E _52 Drivetrain _076176 AXLE AND DIFFERENTIAL _0371053 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43502C 1.INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH

a.

Secure the steering knuckle between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.
C397655

Install the front axle hub sub-assembly and front disc brake dust cover to the steering knuckle with the 4 bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:
·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.




Hide 2.INSTALL FRONT AXLE ASSEMBLY

a.
C397656C01
0,0 0,0 false
V100135

Toyota Body Grease W


Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.


b.

Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.

Torque:
290 N*m (2957 kgf*cm, 214 ft.*lbf)

NOTICE:
·

Do not apply lubricants to the steering knuckle and shock absorber contact surfaces.

·

When installing the nuts, keep the bolts from rotating.



HINT:

The bolts can be installed in either direction, however, make sure that they are both installed in the same direction.



Hide 43420 3.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

a.
C397652C01
2.781,0.406 3.188,0.406 3.188,0.406 3.188,1.573 true 2.927,0.667 3.188,0.667 true 3.115,1.615 3.396,1.823 0.281,0.208 10 false *a
*a Matchmark


Align the matchmarks on the front drive shaft assembly and front axle hub sub-assembly, and connect the front drive shaft assembly to the front axle assembly.

NOTICE:
·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

·

Check that there is no foreign matter on the speed sensor rotor or contact surfaces.

·

Do not damage the front drive shaft outboard joint boot.

·

Do not damage the front disc brake dust cover.

·

Do not damage the speed sensor rotor.




Hide 48069 4.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C397651

Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)


Hide 45470 5.CONNECT TIE ROD ASSEMBLY LH

Hide 43512 6.INSTALL FRONT DISC

Hide 7.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

Hide 43502H 8.INSTALL FRONT AXLE SHAFT NUT LH

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.

Using a 30 mm deep socket wrench, while applying the brakes, temporarily install the front axle shaft nut.

Torque:
294 N*m (2998 kgf*cm, 217 ft.*lbf)

NOTICE:

Stake the front axle shaft nut after inspecting for looseness and runout in the following steps.


HINT:

Keep depressing the brake pedal to prevent the front drive shaft from rotating.



Hide 9.DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

Hide 43512 10.REMOVE FRONT DISC

Hide 11.INSPECT FRONT AXLE HUB BEARING LOOSENESS

Hide 43512 13.INSTALL FRONT DISC

Hide 14.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

Hide 89543 15.INSTALL FRONT SPEED SENSOR LH

a.
C397645C03
0,0 0,0 false
V100135

Hook


Set the 2 front speed sensor LH hooks on the front shock absorber assembly LH.

NOTICE:

Do not twist the front speed sensor when installing it.



b.
C397644

Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Do not twist the front flexible hose when installing it.



c.
C397650

Install the front speed sensor to the steering knuckle with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Prevent foreign matter from attaching to the front speed sensor tip.

·

Firmly insert the front speed sensor body into the steering knuckle before tightening the bolt.

·

After installing the front speed sensor to the steering knuckle, make sure that there is no clearance between the front speed sensor stay and steering knuckle. Also make sure that no foreign matter is stuck between the parts.

·

Do not twist the front speed sensor when installing it.




d.

Engage the clamp.

NOTICE:

Do not twist the front speed sensor when installing it.



Hide 43502H 16.STAKE FRONT AXLE SHAFT NUT LH

a.
C397657

Using a chisel and hammer, stake the front axle shaft nut.


Hide 17.INSTALL FRONT WHEEL

Hide 18.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/o Vacuum Brake Booster)

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION


c.

Perform the following procedure if air bleeding is not necessary:

i.

Turn the power switch on (READY).


ii.

Depress the brake pedal and release it.




Hide 19.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT