Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370835 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Image from Camera for Rear View Monitor is Abnormal  


DESCRIPTION

The display signal from the television camera assembly is transmitted to the radio and display receiver assembly.

WIRING DIAGRAM

E395850E03
5.708,0.552 6.167,0.75 0.458,0.198 10 false CA+ 5.771,1.063 6.229,1.26 0.458,0.198 10 false V+ 5.76,1.521 6.219,1.719 0.458,0.198 10 false V- 5.729,1.917 6.188,2.115 0.458,0.198 10 false CGND 5.438,0.531 5.896,0.729 0.458,0.198 10 false 30 5.469,1.01 5.927,1.208 0.458,0.198 10 false 28 5.479,1.5 5.938,1.698 0.458,0.198 10 false 29 5.49,1.958 5.948,2.156 0.458,0.198 10 false 27 3.333,2.417 4,2.615 0.667,0.198 10 false * 1.531,0.583 1.99,0.781 0.458,0.198 10 false 6 1.563,1.042 2.021,1.24 0.458,0.198 10 false 3 1.573,1.51 2.031,1.708 0.458,0.198 10 false 2 1.573,1.969 2.031,2.167 0.458,0.198 10 false 5 1.125,0.688 1.583,0.885 0.458,0.198 10 false CB+ 1.135,1.094 1.594,1.292 0.458,0.198 10 false CV+ 1.188,1.594 1.646,1.792 0.458,0.198 10 false CV- 1.031,2.031 1.49,2.229 0.458,0.198 10 false CGND 5.24,2.708 5.698,2.906 0.458,0.198 10 false G2 5.229,2.927 6.917,3.292 1.688,0.365 10 false Radio and Display Receiver Assembly 0.26,2.51 0.719,2.708 0.458,0.198 10 false R16 0.24,2.698 2.01,2.958 1.771,0.26 10 false Television Camera Assembly 5.719,2.417 6.177,2.615 0.458,0.198 10 false CSLD 5.479,2.292 5.938,2.49 0.458,0.198 10 false 26 0.625,3.375 1.396,3.563 0.771,0.188 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the radio and display receiver assembly, always replace it with a new one.

If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.

w/ Navigation System:

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

w/ Audio and Visual System (for Radio and Display Type):

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the R16 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-30 (CA+) - R16-6 (CB+) Always Below 1 Ω
G2-28 (V+) - R16-3 (CV+) Always Below 1 Ω
G2-27 (CGND) - R16-5 (CGND) Always Below 1 Ω
G2-29 (V-) - R16-2 (CV-) Always Below 1 Ω
G2-30 (CA+) or R16-6 (CB+) - Body ground Always 10 kΩ or higher
G2-28 (V+) or R16-3 (CV+) - Body ground Always 10 kΩ or higher
G2-27 (CGND) or R16-5 (CGND) - Body ground Always 10 kΩ or higher
G2-29 (V-) or R16-2 (CV-) - Body ground Always 10 kΩ or higher
G2-26 (CSLD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly with its connectors still connected.


E404546C01
5.552,1.146 6.177,1.396 0.625,0.25 3.156,0.427 3.427,0.427 3.427,0.427 3.792,1.625 true 3.333,2.438 3.604,2.438 3.604,2.438 3.906,1.625 true 4.198,1.625 4.469,0.344 4.469,0.344 4.708,0.344 true 5.677,1.208 6.135,1.406 0.458,0.198 10 false G2 4.802,0.281 5.396,0.49 0.594,0.208 10 false CGND 3.135,2.354 3.729,2.563 0.594,0.208 10 false V- 2.875,0.354 3.469,0.563 0.594,0.208 10 false CA+ 1.063,0.646 1.438,0.99 0.375,0.344 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-29 (V-) - Body ground Always Below 1 Ω
G2-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-30 (CA+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.CHECK TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.CHECK TELEVISION CAMERA ASSEMBLY
a.

Remove the radio and display receiver assembly with its connectors still connected.

E404549C01
5.802,1.198 6.219,1.531 0.417,0.333 4.573,3.802 4.74,4.417 4.74,4.417 4.938,4.417 false 4.156,4.396 4.292,4.396 4.292,4.396 4.469,3.854 false 4.156,1.646 4.427,0.448 4.427,0.448 4.625,0.448 true 2.031,3.906 2.198,4.521 2.198,4.521 2.396,4.521 true 1.625,4.5 1.76,4.5 1.76,4.5 1.938,3.958 true 3.563,0.365 3.698,0.365 3.698,0.365 3.979,1.667 true 3.729,3.49 4.188,3.688 0.458,0.198 10 false GND 1.198,3.5 1.656,3.698 0.458,0.198 10 false GND 1.448,4.427 1.906,4.625 0.458,0.198 10 false *d 2.438,4.427 2.896,4.625 0.458,0.198 10 false *e 3.99,4.313 4.448,4.51 0.458,0.198 10 false *d 4.948,4.333 5.406,4.531 0.458,0.198 10 false *e 4.667,0.385 5.302,0.583 0.635,0.198 10 false CGND 3.302,0.313 3.938,0.51 0.635,0.198 10 false V+ 5.885,1.281 6.25,1.51 0.365,0.229 10 false G2 1.146,0.396 1.604,0.594 0.458,0.198 10 false *a 1.125,2.781 1.583,2.979 0.458,0.198 10 false *b 3.906,2.76 4.365,2.958 0.458,0.198 10 false *c
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Check the waveform of the television camera assembly using an oscilloscope.

HINT:
·

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the and display receiver assembly with the connector connected.

·

The video waveform changes according to the image sent by the television camera assembly.



Item Content
Terminal No. (Symbol) G2-28 (V+) - G2-27 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen

OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK TELEVISION CAMERA ASSEMBLY
4.CHECK TELEVISION CAMERA ASSEMBLY
a.

Replace the television camera assembly with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Rear)>REMOVAL


b.

Check if the same malfunction recurs when the rear view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY