Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370834 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the television camera assembly judges as a result of its self check that the signals or signal lines between the television camera assembly and radio and display receiver assembly are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1621 Back Camera Power Supply Failure Television camera assembly power supply failure
·

Harness or connector

·

Television camera assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E378706E24
1.615,0.688 2.104,0.906 0.49,0.219 10 false CA+ 1.479,1.177 1.969,1.396 0.49,0.219 10 false CGND 1.99,0.583 2.479,0.802 0.49,0.219 10 false 30 1.99,1.052 2.479,1.271 0.49,0.219 10 false 27 5.094,1.063 5.583,1.281 0.49,0.219 10 false 5 5.094,0.583 5.583,0.802 0.49,0.219 10 false 6 4.969,1.719 5.458,1.938 0.49,0.219 10 false R15 4.969,1.885 6.917,2.104 1.948,0.219 10 false Television Camera Assembly 0.75,1.708 1.24,1.927 0.49,0.219 10 false G2 0.74,1.885 2.479,2.302 1.74,0.417 10 false Radio and Display Receiver Assembly 5.281,0.708 5.771,0.927 0.49,0.219 10 false CB+ 5.281,1.188 5.771,1.406 0.49,0.219 10 false CGND

CAUTION / NOTICE / HINT

NOTICE:
·

When the "!" mark is displayed on the radio and display receiver assembly after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Disconnect the R15 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-30 (CA+) - R15-6 (CB+) Always Below 1 Ω
G2-27 (CGND) - R15-5 (CGND) Always Below 1 Ω
G2-30 (CA+) or R15-6 (CB+) - Body ground Always 10 kΩ or higher
G2-27 (CGND) or R15-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the R15 television camera assembly connector.

E404546C02
5.552,1.146 6.177,1.396 0.625,0.25 3.156,0.427 3.427,0.427 3.427,0.427 3.792,1.625 true 4.198,1.625 4.469,0.344 4.469,0.344 4.708,0.344 true 5.677,1.208 6.135,1.406 0.458,0.198 10 false G2 4.802,0.281 5.396,0.49 0.594,0.208 10 false CGND 2.875,0.354 3.469,0.563 0.594,0.208 10 false CA+ 1.063,0.646 1.438,0.99 0.375,0.344 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G2-30 (CA+) - G2-27 (CGND) Ignition switch ACC 5.5 to 7.05 V
G2-30 (CA+) - G2-27 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY