Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › FRONT CRANKSHAFT OIL SEAL › 2018.10–2020.08
RM3620E _51 Engine / Hybrid System _076317 A25A-FKS ENGINE MECHANICAL _0371510 FRONT CRANKSHAFT OIL SEAL A

A25A-FKS ENGINE MECHANICAL  FRONT CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for UB80E:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
for UB80F:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
·

Gas leak from exhaust system is repaired

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:
(Click here)
w/o Canister Pump Module:
(Click here)
Replacement of automatic transaxle assembly
for UB80E:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
for UB80F:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
Automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for UB60E:
(Click here)
for UB60F:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Front wheel alignment adjustment
1.

Perform reset memory

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 16361A 2.REMOVE V-RIBBED BELT

Hide 13470 3.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 11301C 4.REMOVE TIMING CHAIN COVER OIL SEAL

a.
A400429C01
0.49,1.271 1.552,1.271 true 0.292,1.177 0.604,1.375 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver, pry out the timing chain cover oil seal.

NOTICE:

After removal, check the crankshaft for damage. If it is damaged, smooth the surface with 400-grit sandpaper.


HINT:

Tape the screwdriver tip before use.