Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY THERMISTOR (for NICKEL METAL HYDRIDE BATTERY)
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0371636 HV BATTERY THERMISTOR(for NICKEL METAL HYDRIDE BATTERY) A

HYBRID / BATTERY CONTROL  HV BATTERY THERMISTOR(for NICKEL METAL HYDRIDE BATTERY)  INSTALLATION  


PROCEDURE

Hide G9282 1.INSTALL HYBRID BATTERY THERMISTOR

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A406118C01
0.313,1.094 0.448,0.292 0.448,0.292 0.677,0.292 true 1.396,1.281 1.573,0.292 1.573,0.292 1.802,0.292 true 3.073,1.26 2.854,0.292 2.854,0.292 2.625,0.292 true 0.698,0.198 1.01,0.354 0.313,0.156 10 false *a 1.823,0.208 2.135,0.365 0.313,0.156 10 false *b 2.448,0.198 2.76,0.354 0.313,0.156 10 false *c
*a 1st Module from the HV Battery Junction Block Assembly Side
(Wire harness color: Blue)
*b 14th Module from the HV Battery Junction Block Assembly Side
(Wire harness color: White)
*c 34th Module from the HV Battery Junction Block Assembly Side
(Wire harness color: Red)


Engage the 3 claws of the hybrid battery thermistor (sensor portions) to install the hybrid battery thermistor to the HV battery.

HINT:

Install each hybrid battery thermistor (sensor portion) to the appropriate location shown in the illustration.



b.
A406106C01
0.563,1.208 0.677,0.26 0.677,0.26 0.885,0.26 true 1.74,1.198 1.854,0.25 1.854,0.25 2.063,0.25 true 1.073,1.229 1.219,2.063 1.219,2.063 1.427,2.063 true 2.615,1.24 2.76,2.063 2.76,2.063 2.969,2.063 true 0.917,0.156 1.229,0.313 0.313,0.156 10 false *a 1.448,1.969 1.76,2.125 0.313,0.156 10 false *b 2.083,0.156 2.396,0.313 0.313,0.156 10 false *c 2.99,1.969 3.302,2.125 0.313,0.156 10 false *d
*a 4th Module from the HV Battery Junction Block Assembly Side
*b 10th Module from the HV Battery Junction Block Assembly Side
*c 18th Module from the HV Battery Junction Block Assembly Side
*d 28th Module from the HV Battery Junction Block Assembly Side


Engage the 4 clamps in the locations shown in the illustration.


c.

Connect the battery voltage sensor connector.


d.

Engage the clamp.


e.
A406119C01
0.563,0.427 0.781,0.427 false 2.26,0.354 2.531,0.354 false 2.76,0.583 2.802,0.313 2.802,0.313 2.979,0.313 false 1.063,0.625 1.104,0.354 1.104,0.354 1.281,0.354 false 0.479,1.01 0.646,1.01 0.646,1.01 0.771,0.719 true 2.146,0.99 2.313,0.99 2.313,0.99 2.458,0.677 true 0.406,0.333 0.719,0.49 0.313,0.156 10 false *1 3.01,0.219 3.323,0.375 0.313,0.156 10 false *a 2.104,0.25 2.417,0.406 0.313,0.156 10 false *1 1.313,0.26 1.625,0.417 0.313,0.156 10 false *a 0.323,0.927 0.635,1.125 0.313,0.198 10 false *b 1.99,0.906 2.302,1.104 0.313,0.198 10 false *b
*1 No. 1 Hybrid Battery Packing
*a Tape
*b Hybrid Battery Thermistor Wire Harness


Engage the 2 claws to install the No. 1 hybrid battery packing to the HV battery.

NOTICE:

Align each piece of tape on the wire harness of the hybrid battery thermistor with the edge of the No. 1 hybrid battery packing as shown in the illustration and then engage the 2 claws to install the No. 1 hybrid battery packing to the HV battery.



f.

Engage the clamp.


Hide G92E1A 2.INSTALL NO. 1 HV BATTERY INTAKE DUCT LH

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Engage the claw of hybrid battery thermistor (sensor portion) to connect the hybrid battery thermistor to the No. 1 HV battery intake duct LH.


b.

Install the No. 1 HV battery intake duct LH to the HV battery with the clip.


Hide G920R 3.INSTALL NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Pull back the rear No. 1 HV battery shield and install the No. 2 hybrid battery shield sub-assembly to the HV battery.

HINT:

Pull back the rear No. 1 HV battery shield until there is sufficient clearance for the stud bolt of the No. 2 hybrid battery shield sub-assembly.



b.

Install the 5 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)