Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV BATTERY (for NICKEL METAL HYDRIDE BATTERY)
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0371635 HV BATTERY(for NICKEL METAL HYDRIDE BATTERY) A

HYBRID / BATTERY CONTROL  HV BATTERY(for NICKEL METAL HYDRIDE BATTERY)  INSTALLATION  


PROCEDURE

Hide G92M8 8.INSTALL UPPER NO. 2 HV BATTERY CARRIER BRACKET

CAUTION:

Be sure to wear insulated gloves.


a.

Install the upper No. 2 HV battery carrier bracket to the HV battery with the 12 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide G9510 9.INSTALL HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.
A430749C01
0.438,3.198 0.75,3.396 0.313,0.198 10 true *a 2.823,3.229 3.063,3.427 0.24,0.198 10 true *a 1.521,0.49 1.74,0.708 0.219,0.219 10 true *a 0.5,0.5 0.719,0.719 0.219,0.219 10 true *b 2.427,0.5 2.646,0.719 0.219,0.219 10 true *a
*a Bolt (A)
(Bolt Length: 25 mm (0.984 in.))
*b Bolt (B)
(Bolt Length: 24 mm (0.945 in.))


Install the HV battery to the vehicle body with the 4 bolts (A), bolt (B).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.

·

As bolts with 3 different lengths are used, make sure to install each bolt to the correct position.

·

If the HV battery has been struck or dropped, replace it.




Hide 82161 10.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the battery voltage sensor connector.


Hide G92F1 11.INSTALL NO. 1 HYBRID BATTERY EXHAUST DUCT

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the claw to install the No. 1 hybrid battery exhaust duct to the HV battery.


b.

Install the clip.


Hide 82161 12.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the 2 clamps.


Hide 899A0 13.INSTALL NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Hide 82161 14.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the HV battery junction block assembly connector.


b.

Connect the electric vehicle battery plug assembly connector.


c.

Engage the clamp.


Hide 821H1 15.CONNECT HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A430743C01
1.844,1.24 2.333,1.24 true 2.396,1.156 2.635,1.354 0.24,0.198 10 true *a
*a Shield Ground


Connect the shield ground to the HV battery.


b.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92N4A 16.INSTALL NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Be sure to wear insulated gloves.


a.
A430751C01
1.448,1.448 1.615,1.448 false 1.25,1.25 1.417,1 1.417,1 1.583,1 true 1.677,1.375 1.99,1.573 0.313,0.198 10 false *1 1.042,0.323 1.354,0.521 0.313,0.198 10 false *b 1.625,0.917 1.938,1.115 0.313,0.198 10 false *a
*1 Battery Cover Lock Striker
*a Button
*b Push


Install the No. 1 HV battery cover panel RH to the HV battery with the 3 bolts and 3 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Install the battery cover lock striker, then push the button to lock it.


Hide G9230 17.INSTALL BATTERY COOLING BLOWER ASSEMBLY

Hide 19.PERFORM INITIALIZATION