Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
72443B
1.INSTALL VERTICAL ADJUSTER GEAR LH (for Driver Side)
Install the vertical adjuster gear LH.
| *a | Stud Bolt of the Front Vertical Adjuster Brake Sub-assembly RH |
| *b | Hole of the Front Seat Adjuster Assembly RH |
Install the vertical adjuster brake sub-assembly LH.
Make sure to insert the stud bolt of the vertical adjuster brake sub-assembly LH into the hole of the front seat adjuster assembly LH as shown in the illustration.
Install the vertical adjuster spacer.
Install the vertical adjuster plate with the 3 nuts.
72125T
2.INSTALL FRONT SEAT REAR UPPER TRACK COVER LH
Use the same procedure for both sides.
|
Install in this Direction |
Attach the claw to install the front seat rear upper track cover LH as shown in the illustration.
72266
3.INSTALL SEAT UPPER TRACK RAIL COVER LH
Use the same procedure for both sides.
|
Install in this Direction |
Attach the claw to install the seat upper track rail cover LH as shown in the illustration.
72211C
4.INSTALL SEAT TRACK ADJUSTING HANDLE
Attach the claw to install the seat track adjusting handle.
71052A
5.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH
| *a | Hook A |
| *b | Hook B |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in the installation direction (1) shown in the illustration to attach the hook A.
Push in the installation direction (2) shown in the illustration, attach the hook B to install the front seat cushion spring sub-assembly LH.
6.INSTALL CONNECTOR MALE HOUSING (w/ Dummy Connector)
Attach the claw to install the connector male housing.
82191A
7.INSTALL FRONT SEAT WIRE RH (for Front Passenger Side, w/ Occupant Classification System)
Attach the claw.
Attach the clamp to install the front seat wire RH.
7181B
8.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER LH
Attach the guide.
Install the front seat cushion wire harness holder LH with the 2 screws.
for Front Passenger Side, w/ Occupant Classification System:
Connect the 2 connectors.
82191
9.INSTALL FRONT SEAT WIRE RH (w/ Climate Control Seat System)
| *a | w/ Seat Heater System |
Attach the claw.
Attach the clamp to install the front seat wire RH.
85860A
10.INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY RH (w/ Climate Control Seat System)
Attach the hook.
Install the seat cushion climate control blower assembly RH with the 2 bolts.
Connect the connector.
71874A
11.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)
| *a | Hook |
| *b | Guide |
|
Install in this Direction |
Attach the guide and claw as shown in the illustration.
Attach the hook to install the front seat lower cushion shield LH.
71873U
12.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)
| *a | Hook |
| *b | Guide |
|
Install in this Direction |
Attach the guide and claw as shown in the illustration.
Attach the hook to install the front seat lower cushion shield RH.
71876G
13.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER (for Driver Side)
|
Install in this Direction |
Attach the hook and claw to install the LH seat reclining adjuster inside cover as shown in the illustration.
71876F
14.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER (for Front Passenger Side)
| *a | Hook |
| *b | Clamp |
|
Install in this Direction |
Attach the hook and claw to install the RH seat reclining adjuster inside cover as shown in the illustration.
w/ Occupant Classification System:
Attach the clamp.
71875G
15.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER (for Driver Side)
|
Install in this Direction |
Attach the hook and claw to install the LH seat reclining adjuster inside cover as shown in the illustration.
71875F
16.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER (for Front Passenger Side)
|
Install in this Direction |
Attach the hook and claw to install the RH seat reclining adjuster inside cover as shown in the illustration.
w/ Climate Control Seat System:
Attach the clamp and claw.
82667D
17.INSTALL CONNECTOR HOLDER (for Front Passenger Side, w/o Occupant Classification System)
Attach the claw to install the connector holder.
739F0
18.INSTALL FRONT SEAT CUSHION AIRBAG ASSEMBLY RH (for Front Passenger Side, w/ Occupant Classification System)
87510L
19.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
87510K
20.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
71072S
21.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
When installing a separate type front seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
for Standard Seat Type:
Attach the hook to install the separate type front seat cushion cover.
Be careful not to dirty or damage the separate type front seat cushion cover.
for Sports Seat Type:
Attach the hook to install the separate type front seat cushion cover.
Be careful not to dirty or damage the separate type front seat cushion cover.
| *a | Band |
|
Install in this Direction |
Attach the band.
22.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Attach the hook to install the separate type front seat cushion cover with pad.
Attach the hook.
for Front Passenger Side, w/o Occupant Classification System:
Attach the claw.
w/o Climate Control Seat System, w/ Seat Heater System:
Attach the claw and clamp.
w/ Climate Control Seat System, w/ Seat Heater System:
Connect the connector.
Attach the clamp.
71759D
23.INSTALL FRONT NO. 2 SEATBACK HOOK
Attach the claw to install 2 new front No. 2 seatback hooks.
Check that the claw of the front seatback hooks are securely attached.
71587B
24.INSTALL FRONT SEATBACK EDGE PROTECTOR
Attach the claw to install the 2 front seatback edge protectors.
71054S
25.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY LH
w/ Climate Control Seat System:
|
Install in this Direction |
Install the front seatback felt RH.
|
Install in this Direction |
Set the front seatback spring sub-assembly LH to the front seatback frame assembly LH as shown in the illustration.
Attach the clamp.
8219A
26.INSTALL FRONT NO. 2 SEAT WIRE RH (w/ Climate Control Seat System, for LHD)
Attach the clamp to install the front No. 2 seat wire RH.
Connect the connector.
8219B
27.INSTALL FRONT NO. 2 SEAT WIRE LH (w/ Climate Control Seat System, for RHD)
Attach the clamp to install the front No. 2 seat wire LH.
Connect the connector.
73920A
28.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH
87510N
29.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
87510M
30.INSTALL FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)
71074S
31.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
When installing a separate type front seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
for Standard Seat Type:
Attach the hook to install the separate type front seatback cover to the separate type front seatback pad.
Be careful not to dirty or damage the separate type front seatback cover.
for Sports Seat Type:
Attach the hook to install the separate type front seatback cover to the separate type front seatback pad.
Be careful not to dirty or damage the separate type front seatback cover.
32.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad.
|
Install in this Direction |
Attach the claw to install the 2 front seat headrest supports as shown in the illustration.
Close the 2 fasteners.
w/ Seat Heater System:
Attach the clamp.
| *a | Outshoot |
Attach the hook.
Be careful not to overlap on the route of the wire harness.
Pass the wire harness through the outside of the outshoot.
33.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Attach the guide to install the separate type front seatback assembly to the separate type front seat cushion assembly.
Temporarily install the separate type front seatback assembly with the 4 bolts.
Tighten the 4 bolts.
Attach the claw and clamp.
Attach the claw first.
w/ Seat Heater System:
Attach the clamp.
Connect the connector.
w/ Climate Control Seat System:
Attach the clamp.
Connect the connector.
Attach the hook.
Attach the band.
72498A
34.INSTALL VERTICAL ADJUSTER BRACKET COVER LH (for Driver Side)
Attach the guide and claw to install the vertical adjuster bracket cover LH.
71862
35.INSTALL FRONT SEAT INNER CUSHION SHIELD LH (for Driver Side)
|
Install in this Direction |
Attach the claw as shown in the illustration.
|
Install in this Direction |
Attach the claw and guide as shown in the illustration.
|
Install in this Direction |
Attach the claw to install the front seat inner cushion shield LH as shown in the illustration.
71861
36.INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
|
Install in this Direction |
Attach the claw as shown in the illustration.
|
Install in this Direction |
Attach the claw and guide as shown in the illustration.
|
Install in this Direction |
Attach the claw to install the front seat inner cushion shield RH as shown in the illustration.
71812D
37.INSTALL FRONT SEAT CUSHION SHIELD LH (for Driver Side)
|
Install in this Direction |
Attach the guide as shown in the illustration.
|
Install in this Direction |
Attach the claw as shown in the illustration.
|
Install in this Direction |
Attach the claw and guide as shown in the illustration.
|
Install in this Direction |
Attach the claw to install the front seat cushion shield LH as shown in the illustration.
71811D
38.INSTALL FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)
|
Install in this Direction |
Attach the guide as shown in the illustration.
|
Install in this Direction |
Attach the claw as shown in the illustration.
|
Install in this Direction |
Attach the claw and guide as shown in the illustration.
|
Install in this Direction |
Attach the claw to install the front seat cushion shield RH as shown in the illustration.
71849
39.INSTALL SEAT ADJUSTER COVER CAP LH (for Driver Side)
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Push in the installation direction (1) shown in the illustration to attach the guide.
Push in the installation direction (2) shown in the illustration and attach the claw to install the seat adjuster cover cap LH.
72526A
40.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
Attach the guide to install the reclining adjuster release handle LH.
72552B
41.INSTALL RECLINING HINGE COVER LH
|
Install in this Direction |
Attach the guide and claw to install the reclining hinge cover LH as shown in the illustration.
72495
42.INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)
|
Install in this Direction |
Attach the claw to install the vertical adjusting handle LH as shown in the illustration.
73240
43.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
73230
44.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
89952
45.INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side, w/ Occupant Classification System)
87501A
46.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System, w/ Climate Control Seat System)