Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB › 2018.10–2020.08
RM3620E _52 Drivetrain _076176 AXLE AND DIFFERENTIAL _0371056 REAR AXLE HUB A

AXLE AND DIFFERENTIAL  REAR AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle hub removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.RELEASE PARKING BRAKE

Hide 2.DISABLE BRAKE CONTROL (w/o Vacuum Brake Booster)

Hide 3.REMOVE REAR WHEEL

Hide 890C0A 4.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C397667

Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




Hide 42312B 5.REMOVE REAR AXLE SHAFT NUT (for 4WD/AWD)

a.
C407434N01
2.375,1.5 2.5,1.167 2.5,1.167 2.667,1.167 false 2.729,1.094 3.188,1.292 0.458,0.198 10 false SST

Using SST and a hammer, release the staked part of the rear axle shaft nut.

SST
09930-00010  (09931-00010, 09931-00020)

NOTICE:

Loosen the staked part of the rear axle shaft nut completely, otherwise the threads of the rear drive shaft assembly may be damaged.



b.

While applying the brakes, remove the rear axle shaft nut.


Hide 7.DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH

Hide 42431 8.REMOVE REAR DISC

Hide 890C0A 9.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for 2WD)

a.
C397668C01
1.25,1.917 1.5,1.917 1.5,1.917 1.5,1.448 true 1,1.833 1.229,2.01 0.229,0.177 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disconnect the No. 2 parking brake wire assembly connector from the rear axle hub and bearing assembly.

NOTICE:

Be careful not to damage the rear axle hub and bearing assembly and connector cover.



Hide 89544E 10.DISCONNECT SKID CONTROL SENSOR (for 4WD/AWD)

a.
C397676

Remove the bolt and disconnect the skid control sensor from the rear axle carrier sub-assembly.

NOTICE:
·

Keep the tip of the skid control sensor and installation hole free of foreign matter.

·

Do not rotate or apply excessive force to the skid control sensor when removing it from the rear axle carrier sub-assembly. Rotating or applying excessive force may result in damage to the skid control sensor.




Hide 42450B 11.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH (for 2WD)

a.
C397669

Remove the 4 bolts, rear axle hub and bearing assembly and rear disc brake dust cover sub-assembly from the rear axle carrier sub-assembly.


Hide 42450B 12.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD/AWD)

a.
C407435C01
2.5,1.917 2.5,1.021 2.5,1.021 2.854,1.021 true 2.5,1.313 2.917,1.313 true 2.448,1.938 2.781,2.146 0.333,0.208 10 false *a
*a Matchmark


Place matchmarks on the rear drive shaft assembly and the rear axle hub and bearing assembly.


b.
C407436

Using a plastic hammer, separate the rear drive shaft assembly from the rear axle hub and bearing assembly.

NOTICE:
·

Do not damage the rear drive shaft outboard joint boot.

·

Do not push the rear axle hub and bearing assembly towards the outside of the vehicle any further than necessary.



HINT:

If it is difficult to separate the rear drive shaft assembly rear axle hub and bearing assembly, tap the end of the rear drive shaft assembly using a brass bar and a hammer.



c.
C407437

Remove the 4 bolts, rear axle hub and bearing assembly and rear disc brake dust cover sub-assembly from the rear axle carrier sub-assembly.