The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier removal/installation are shown below.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
1.RELEASE PARKING BRAKE
for Manual Transaxle: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
except Manual Transaxle: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
2.REMOVE REAR WHEEL
48738C
3.REMOVE LOWER NO. 2 CONTROL ARM COVER (w/ Cover)
890C0A
4.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.
Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.
Remove the bolt and disconnect the skid control sensor from the rear axle carrier sub-assembly.
Keep the tip of the skid control sensor and installation hole free of foreign matter.
Do not rotate or apply excessive force to the skid control sensor when removing it from the rear axle carrier sub-assembly. Rotating or applying excessive force may result in damage to the skid control sensor.
Remove the nut, disengage the 2 clamps and separate the No. 2 parking brake wire assembly from the rear flexible hose bracket and rear trailing arm assembly.
47319F
5.DISCONNECT REAR FLEXIBLE HOSE LH
Remove the bolt and disconnect the rear flexible hose LH from the rear flexible hose bracket.
42312B
6.REMOVE REAR AXLE SHAFT NUT
7.DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH
Remove the 2 bolts and disconnect the rear disc brake caliper assembly from the rear axle carrier sub-assembly.
Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.
42431
8.REMOVE REAR DISC
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
42450B
9.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH
47352B
10.REMOVE NO. 2 FLEXIBLE HOSE BRACKET
Remove the bolt and flexible hose bracket from the rear axle carrier sub-assembly.
89408C
11.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (for LH Side)
48840A
12.REMOVE REAR STABILIZER LINK ASSEMBLY LH
48231B
13.REMOVE REAR COIL SPRING LH
48258C
14.REMOVE REAR LOWER COIL SPRING INSULATOR LH
48720A
15.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
Remove the bolt, nut and rear No. 1 suspension arm assembly LH from the rear axle carrier sub-assembly and rear suspension member sub-assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
16.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY
Loosen the 3 bolts of the rear trailing arm assembly.
| *1 | Rear Axle Carrier Pin |
Loosen the nut of the rear shock absorber assembly.
Hold the rear axle carrier pin while rotating the nut.
| *a | Wooden Block |
| *b | Jack |
Using a jack and wooden block, support the rear axle carrier sub-assembly.
When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.
Make sure to perform this operation with the vehicle kept as low as possible.
Loosen the bolt (A).
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
Remove the 3 bolts, nut and disconnect the rear trailing arm assembly from the rear axle carrier sub-assembly.
Remove the nut and disconnect the rear shock absorber assembly from the rear axle carrier sub-assembly.
Hold the rear axle carrier pin while rotating the nut.
Remove the bolt (A), nut and rear axle carrier sub-assembly from the rear upper control arm assembly.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.