Home › Suspension › REAR SUSPENSION › REAR TRAILING ARM
RM3620E _53 Suspension _076491 REAR SUSPENSION _0372237 REAR TRAILING ARM A

REAR SUSPENSION  REAR TRAILING ARM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear trailing arm assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for HV model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for HV model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (for Gasoline model) (Click here)
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 53896B 2.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 53895B 3.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 51420 5.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 58166A 6.REMOVE FRONT FLOOR COVER LH (w/ Floor Under Cover)

Hide 58166A 7.REMOVE FRONT FLOOR COVER RH (w/ Floor Under Cover)

Hide 58399D 8.REMOVE NO. 2 FLOOR UNDER COVER (w/ Floor Under Cover)

Hide 58398F 9.REMOVE NO. 1 FLOOR UNDER COVER (w/ Floor Under Cover)

Hide 48738C 10.REMOVE LOWER NO. 2 CONTROL ARM COVER (w/ Cover)

Hide 890C0A 11.SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.
C403442

Disengage the 2 clamps.


b.

Remove the nut and separate the No. 2 parking brake wire assembly from the rear trailing arm assembly.


Hide 48780E 12.REMOVE REAR TRAILING ARM ASSEMBLY

a.
C403443C01
0.24,1.583 0.406,1.583 0.406,1.583 0.906,1.417 false 1.917,1.667 2.25,1.667 false 0.063,1.49 0.479,1.823 0.417,0.333 10 false *a 2.292,1.604 2.625,1.938 0.333,0.333 10 false *b
*a Wooden Block
*b Transmission Jack


Using a transmission jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




b.
C403444

Remove the 3 bolts, nut and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.


c.
C403445

Remove the 2 bolts and rear trailing arm assembly.