Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › CYLINDER HEAD › 2018.10–2020.08
RM3620E _51 Engine / Hybrid System _076500 M20A-FKS ENGINE MECHANICAL _0372439 CYLINDER HEAD A

M20A-FKS ENGINE MECHANICAL  CYLINDER HEAD  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for M20A-FKS:

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
for K120:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for K120F:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
·

Throttle body with motor assembly

·

Cam timing control motor with EDU assembly (Including removal and installation)

·

Camshaft timing gear assembly (Including removal and installation)

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pump (for low pressure side)

·

Fuel pump assembly (for high pressure side)

·

Fuel pressure sensor (for low pressure side)

·

Fuel pressure sensor (for high pressure side)

·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

EGR valve assembly

·

Air intake system parts

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly Air bleed oil pump with motor assembly Stop and start system (Click here)
for K120, K120F:
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for K120:(Click here)
for K120F:(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Front wheel alignment adjustment
1.

Perform reset memory

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 13711 1.REMOVE INTAKE VALVE

a.
A426802N01
2.146,1.833 1.802,2 false 1.563,0.135 0.958,0.438 true 1.469,1.917 1.927,2.115 0.458,0.198 10 false SST 1.635,0.052 2.094,0.25 0.458,0.198 10 false SST

Using SST, compress each compression spring and remove the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 8 valve spring retainers, 8 compression springs and 8 intake valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13715 2.REMOVE EXHAUST VALVE

a.
A426803N01
1.542,1.75 1.729,1.958 false 1.885,0.156 2.323,0.24 true 1.771,1.865 2.229,2.063 0.458,0.198 10 false SST 1.573,0.073 2.031,0.271 0.458,0.198 10 false SST

Using SST, compress each compression spring and remove the 8 valve spring retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 8 valve spring retainers, 8 compression springs and 8 exhaust valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 3.REMOVE VALVE STEM OIL SEAL

a.
A426804

Using needle-nose pliers, remove the 16 valve stem oil seals.


Hide 4.REMOVE VALVE SPRING SEAT

a.
A426805

Using compressed air and a Magnet Hand, remove the 16 valve spring seats from the cylinder head sub-assembly by blowing air onto them.


Hide 11117E 5.REMOVE NO. 1 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.


A426806

a.

Using a 6 mm straight hexagon wrench, remove the 4 No. 1 straight screw plugs from the cylinder head sub-assembly.


Hide 6.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A426807

Using an E8 "TORX" socket wrench, remove the 7 stud bolts.