Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING (for Moon Roof)
RM3620E _59 Vehicle Exterior _076526 SLIDING ROOF / CONVERTIBLE _0372468 SLIDING ROOF HOUSING(for Moon Roof) A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING(for Moon Roof)  INSTALLATION  


PROCEDURE

Hide 63203F 1.INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY

a.

Temporarily install the sliding roof housing sub-assembly with the 6 nuts and 4 bolts.

B527493


b.

Tighten the 6 nuts and 4 bolts.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:
B474971

If the removed nut is the same shape as that shown in the illustration, replace it the supplied replacement part.



c.

Install the sliding roof drain hose clamp to the sliding roof drain hose.


Hide 2.CONNECT SLIDING ROOF DRAIN HOSE

a.

Connect the sliding roof 4 drain hoses.

NOTICE:

Make sure the sliding roof drain hose is securely inserted to prevent water leakage.


HINT:

Slide the hose to the base of the drain pipe.


i.

for Front Side:

B527485C01
1.906,3.01 2.229,3.156 true 0.229,0.167 0.552,0.417 0.323,0.25 12 false *A 2.271,3.094 2.521,3.323 0.25,0.229 10 true *a
*A Front Side - -
*a Marking - -
V100135

Sliding Roof Drain Hose Clamp
V100136

Rear Side


HINT:

Use the same procedure for the other side.



ii.

for Rear Side:

B527486C01
1.979,3.021 2.229,3.135 true 0.229,0.167 0.552,0.417 0.323,0.25 12 false *A 2.271,3.094 2.521,3.323 0.25,0.229 10 true *a
*A Rear Side - -
*a Marking - -
V100135

Sliding Roof Drain Hose Clamp
V100136

Inside


HINT:

Use the same procedure for the other side.




b.

Attach the claw to secure the sliding roof drain hose.


Hide 62180A 3.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 4.INSTALL CURTAIN SHIELD AIR BAG ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 63201P 5.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

NOTICE:
·

Carrying the sliding roof glass sub-assembly from the vehicle must be performed by multiple people.

·

Be careful not to damage the sliding roof glass sub-assembly, body exterior or interior parts.



a.
B538107N01
1.198,0.427 1.354,0.625 0.156,0.198 10 false a

Measure the width (a) of the sliding roof weatherstrip.

HINT:

This measurement will be used in a later step.



b.

Using a T25 "TORX" socket wrench, temporarily install the sliding roof panel sub-assembly with the 4 "TORX" screws.


c.

Perform a level check.

B527487N01
4.281,0.271 5.917,0.51 1.635,0.24 10 false A-A, B-B, C-C, D-D 2.385,0.698 2.552,0.885 0.167,0.188 10 true B 4.5,0.865 4.823,1.125 0.323,0.26 10 false a 2.385,0.948 2.542,1.135 0.156,0.188 10 true B 1.781,1.063 1.938,1.25 0.156,0.188 10 true A 2.052,1.063 2.188,1.229 0.135,0.167 10 true A 2.604,1.542 2.76,1.729 0.156,0.188 10 true C 2.313,1.531 2.469,1.719 0.156,0.188 10 true C 2.094,1.802 2.25,1.99 0.156,0.188 10 true D 2.292,2.01 2.448,2.198 0.156,0.188 10 true D

i.

Check the difference in level "a" between the roof panel and the upper surface of the sliding roof weatherstrip when the sliding roof panel sub-assembly is fully closed.

HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.


Standard:
Area Measurement Area Measurement
A-A (a) 0 + 1.0 mm (0 + 0.0394 in.)
0 - 2.0 mm (0 - 0.0787 in.)
B-B (a) 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.5 mm (0 - 0.0591 in.)
C-C (a) 0 + 2.0 mm (0 + 0.0787 in.)
0 - 1.0 mm (0 - 0.0394 in.)
D-D (a) 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.0 mm (0 - 0.0394 in.)




d.

Check the deformation of the sliding roof weatherstrip.

B527488N01
4.979,0.135 5.302,0.438 0.323,0.302 10 false a 5,1.49 5.323,1.792 0.323,0.302 10 false b 4.115,1.188 5.813,1.396 1.698,0.208 10 true A-A, B-B, C-C, D-D, E-E 2.365,0.708 2.552,0.906 0.188,0.198 10 true B 2.375,0.948 2.563,1.146 0.188,0.198 10 true B 2.604,1.542 2.75,1.729 0.146,0.188 10 true C 2.323,1.542 2.469,1.719 0.146,0.177 10 true C 1.76,1.073 1.927,1.25 0.167,0.177 10 true A 2.052,1.073 2.208,1.25 0.156,0.177 10 true A 1.854,1.542 2,1.719 0.146,0.177 10 true E 1.646,1.667 1.792,1.844 0.146,0.177 10 true E 2.188,1.865 2.333,2.042 0.146,0.177 10 true D 2.406,2.042 2.552,2.219 0.146,0.177 10 true D

i.

With the sliding roof panel sub-assembly in the fully closed position, measure the width (b) of the sliding roof weatherstrip and, using the width (a) measured in step a., calculate the deformation of the sliding roof weatherstrip (a - b).

Standard:
Area Measurement Area Measurement
A-A (a - b) 0.5 mm (0.0197 in.) to 2.5 mm (0.0984 in.) B-B (a - b) 0.5 mm (0.0197 in.) to 2.5 mm (0.0984 in.)
C-C (a - b) 0.5 mm (0.0197 in.) to 2.5 mm (0.0984 in.) D-D (a - b) 0.8 mm (0.0315 in.) to 2.8 mm (0.110 in.)
E-E (a - b) 0.8 mm (0.0315 in.) to 2.8 mm (0.110 in.) - -




e.

After adjusting the sliding roof panel sub-assembly, using a T25 "TORX" socket wrench, install the sliding roof panel sub-assembly with the 4 "TORX" screws.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 6. CHECK FOR WATER LEAK

a.

After adjusting the sliding roof panel sub-assembly, check for water leakage into the vehicle interior.


b.

If there are any leaks, readjust the sliding roof panel sub-assembly.


Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL



c.

for M20A-FKS:

Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 63218S 8.INSTALL SLIDING ROOF SIDE GARNISH LH

a.

Move the sliding roof glass sub-assembly to the fully tilted up position.


b.

Attach the guide to install the sliding roof side garnish LH.


Hide 63217R 9.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 12.PERFORM SYSTEM INITIALIZATION AND CALIBRATION