Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0374463 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during curtain shield airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
w/ Occupant Classification System:
Front passenger seat
Zero point calibration (Occupant classification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
w/ Occupant Classification System:
Front passenger seat
Zero point calibration (Occupant classification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 6.REMOVE ROOF HEADLINING ASSEMBLY

Hide 62180A 7.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH (except Rollover Type)

CAUTION:
B399183C01
0.667,0.5 0.823,0.698 0.156,0.198 10 false .
V100155

Deployment Side


·

When storing the curtain shield airbag assembly LH, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B523116C01
0.771,0.667 1.333,0.448 true 1.396,0.344 1.708,0.5 0.313,0.156 10 false *a
*a Lock Button
V100155

Protective Tape
V113147

Release in this Direction


Using a screwdriver, release the lock button and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Tape the screwdriver tip before use.



d.
B524511

for LH Side:

Detach the wire harness clamp.


e.

Remove the curtain shield airbag assembly LH deployment portion in the following order.

1.

Using No. 2 needle-nose pliers, remove the 4 pins from the 3 clips and roof side inner garnish clip.

2.

Using 2 thin-bladed screwdrivers, detach the claw and remove the 3 clips and roof side inner garnish clip together with the curtain shield airbag assembly LH deployment portion.

3.

Detach the claw.


B523122C02
2.031,0.396 2.198,0.313 true 3.75,0.396 3.917,0.313 true 4.896,0.417 5.063,0.333 true 6.635,0.417 6.802,0.333 true 4.698,2.01 4.906,2.208 0.208,0.198 10 true *2 5.469,2.125 5.677,2.302 0.208,0.177 10 true *2 3.99,1.906 4.198,2.083 0.208,0.177 10 true *1 2.26,1.875 2.469,2.052 0.208,0.177 10 true *2 2.219,0.25 2.469,0.448 0.25,0.198 10 false *a 5.063,0.25 5.313,0.448 0.25,0.198 10 false *a 3.948,0.24 4.198,0.438 0.25,0.198 10 false *b 6.813,0.24 7.063,0.438 0.25,0.198 10 false *b
*1 Roof Side Inner Garnish Clip *2 Clip
*a No. 2 Needle-Nose Pliers *b Thin-Bladed Screwdriver
V113147

Remove in this Direction - -



f.

Remove the curtain shield airbag assembly LH inflator in the following order.

CAUTION:

The bolt must not be reused.


1.

Remove the bolt and detach the hook to remove the curtain shield airbag assembly LH strap.

2.

Remove the bolt and rear side of the curtain shield airbag assembly LH deployment portion.

3.

Pull down the curtain shield airbag assembly LH deployment portion and remove the 2 bolts.

4.

Detach the hook to remove the curtain shield airbag assembly LH inflator.


B523124C01
6.344,1.01 6.552,1.208 0.208,0.198 10 true *a 1.094,0.729 1.302,0.927 0.208,0.198 10 true *b 1.135,2.167 1.344,2.365 0.208,0.198 10 true *c
*a Strap *b Rear Side Bolt
*c Curtain Shield Airbag Assembly LH Inflator - -
V113147

Pull Down in this Direction - -



g.

When reusing the curtain shield airbag assembly LH:

CAUTION:

Do not reuse the clip, roof side inner garnish clip and curtain shield airbag clip spacer.


i.

Detach the claw and remove the clip and curtain shield airbag clip spacer from the front side of the curtain shield airbag assembly LH.


ii.

Detach the claw and remove the 2 clips and roof side inner garnish clip.

B523128C01
0.51,2.063 0.875,2.063 true 0.229,1.406 0.542,1.563 0.313,0.156 10 false *1 0.344,1.958 0.656,2.115 0.313,0.156 10 false *2 3.563,2.26 3.875,2.417 0.313,0.156 10 false *1 2.094,0.167 2.406,0.323 0.313,0.156 10 false *3 5.521,2.125 5.833,2.281 0.313,0.156 10 false *1
*1 Clip *2 Curtain Shield Airbag Clip Spacer
*3 Roof Side Inner Garnish Clip - -




Hide 62180A 8.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH (for Rollover Type)

CAUTION:
B399183C01
0.667,0.5 0.823,0.698 0.156,0.198 10 false .
V100155

Deployment Side


·

When storing the curtain shield airbag assembly LH, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.
B535376C01
0.771,0.667 1.333,0.448 true 1.396,0.344 1.708,0.5 0.313,0.156 10 false *a
*a Lock Button
V100155

Protective Tape
V113147

Release in this Direction


Using a screwdriver, release the lock button and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Tape the screwdriver tip before use.



d.
B524511

for LH Side:

Detach the wire harness clamp.


e.

Remove the curtain shield airbag assembly LH deployment portion in the following order.

CAUTION:

Do not reuse the clip A and roof side inner garnish clip.


1.

Using No. 2 needle-nose pliers, remove the 4 pins from the 3 clips A and roof side inner garnish clip.

2.

Using 2 thin-bladed screwdrivers, detach the claw and remove the 3 clips A and roof side inner garnish clip together with the curtain shield airbag assembly LH deployment portion.

3.

Detach the claw.


B524517C02
1.938,0.406 2.125,0.333 true 3.656,0.406 3.844,0.333 true 4.802,0.417 4.99,0.344 true 6.542,0.427 6.729,0.354 true 4.646,2.052 4.833,2.26 0.188,0.208 10 true *1 5.375,2.156 5.563,2.333 0.188,0.177 10 true *2 3.917,1.917 4.104,2.094 0.188,0.177 10 true *2 2.219,1.875 2.406,2.052 0.188,0.177 10 true *2 2.125,0.219 2.438,0.417 0.313,0.198 10 false *a 5,0.219 5.313,0.417 0.313,0.198 10 false *a 3.854,0.219 4.167,0.417 0.313,0.198 10 false *b 6.719,0.229 7.031,0.427 0.313,0.198 10 false *b
*1 Roof Side Inner Garnish Clip *2 Clip A
*a No. 2 Needle-Nose Pliers *b Thin-Bladed Screwdriver
V113147

Remove in this Direction - -



f.

Remove the curtain shield airbag assembly LH inflator in the following order.

CAUTION:

The bolt and clip B must not be reused.


1.

Remove the bolt and detach the hook to remove the curtain shield airbag assembly LH strap.

2.

Remove the bolt and rear side of the curtain shield airbag assembly LH deployment portion.

3.

Remove the 4 bolts from the bracket.

4.

Using a clip remover, detach the clip B to remove the bracket.

HINT:

Tape the clip remover tip before use.


5.

Pull down the curtain shield airbag assembly LH deployment portion and remove the 2 bolts and curtain shield airbag assembly LH inflator.


B524518C01
6.156,1.771 6.333,1.969 0.177,0.198 10 true *a 0.917,1.615 1.094,1.813 0.177,0.198 10 true *b 1.99,0.583 2.167,0.781 0.177,0.198 10 true *c 1.063,3.177 1.24,3.375 0.177,0.198 10 true *d
*a Strap *b Rear Side Bolt
*c Bracket *d Curtain Shield Airbag Assembly LH Inflator
V113147

Pull Down in this Direction
V100155

Protective Tape



g.

When reusing the curtain shield airbag assembly LH:

CAUTION:

Do not reuse the clip A, clip B, roof side inner garnish clip and curtain shield airbag clip spacer.


i.

Detach the claw and remove the clip A and curtain shield airbag clip spacer from the front side of the curtain shield airbag assembly LH.


ii.

Detach the claw and remove the 2 clips A and roof side inner garnish clip.


iii.

Remove the 2 clips B.

B524519C01
0.49,2.906 0.885,2.906 true 0.24,2.229 0.552,2.385 0.313,0.156 10 false *1 0.313,2.802 0.625,2.958 0.313,0.156 10 false *2 1.292,0.656 1.604,0.813 0.313,0.156 10 false *1 2.844,3.104 3.042,3.271 0.198,0.167 10 true *4 3.01,0.51 3.323,0.667 0.313,0.156 10 false *3 5.542,2.708 5.854,2.865 0.313,0.156 10 false *1
*1 Clip A *2 Curtain Shield Airbag Clip Spacer
*3 Roof Side Inner Garnish Clip *4 Clip B
V113147

Remove in this Direction - -