Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM3620E _59 Vehicle Exterior _076564 WIPER / WASHER _0372553 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Headlight Cleaner Motor and Relay Circuit  


DESCRIPTION

The headlight ECU sub-assembly RH controls the headlight cleaner motor and pump assembly.

WIRING DIAGRAM

E405258E05
4.469,0.635 6.031,0.854 1.563,0.219 10 false from Auxiliary Battery 3.219,0.813 3.927,1.031 0.708,0.219 10 false H-LP CLN 1.375,0.99 1.833,1.188 0.458,0.198 10 false A10 1.365,1.156 2.896,1.531 1.531,0.375 10 false Headlight Cleaner Motor and Pump Assembly 2.76,0.531 2.917,0.729 0.156,0.198 10 false 2 1.375,0.521 1.531,0.719 0.156,0.198 10 false 1 3.135,2.375 5.094,2.76 1.958,0.385 10 false Headlight Cleaner Control Relay Assembly (H-LP CLN) 1.698,3.104 2.729,3.323 1.031,0.219 10 false ECU-IG1 NO.3 0.323,2.917 1.25,3.469 0.927,0.552 10 false from IG1 NO.1 Relay 5.719,5.115 7.042,5.49 1.323,0.375 10 false Headlight ECU Sub-assembly RH 5.729,4.948 6.188,5.146 0.458,0.198 10 false A12 6,4.521 6.458,4.719 0.458,0.198 10 false GND 6.021,2.083 6.479,2.281 0.458,0.198 10 false HLC 6.01,2.927 6.323,3.125 0.313,0.198 10 false IG 0.75,5.323 2.5,5.583 1.75,0.26 10 false : CAN Communication Line 3.385,4.365 4.469,4.594 1.083,0.229 10 false Steering Sensor 5.729,4.417 6,4.646 0.271,0.229 10 false 12 5.76,2.802 5.917,3 0.156,0.198 10 false 4 5.75,1.938 5.906,2.135 0.156,0.198 10 false 7 4.25,1.969 4.406,2.167 0.156,0.198 10 false 2 4.24,1.573 4.396,1.771 0.156,0.198 10 false 5 3.406,1.969 3.563,2.167 0.156,0.198 10 false 1 3.396,1.573 3.552,1.771 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

First check that the front washer operates normally.

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>OPERATION CHECK

·

Check that the lighting system is normal before performing the following procedure.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (HEADLIGHT CLEANER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / HL AutoLeveling (Sub) / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Headlight Cleaner Function to operate the headlight cleaner motor and pump assembly OFF or ON -
Body Electrical > HL AutoLeveling (Sub) > Active Test
Tester Display
Headlight Cleaner
50004 414 1
OK:

Headlight cleaner motor and pump assembly operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FRONT WINDOW WASHER SWITCH)

NG

3.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
2.READ VALUE USING GTS (FRONT WINDOW WASHER SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / HL AutoLeveling (Sub) / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > HL AutoLeveling (Sub) > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Window Washer Switch Windshield wiper switch assembly (washer switch) condition OFF or ON OFF: Windshield wiper switch assembly (washer switch) off
ON: Windshield wiper switch assembly (washer switch) on
-
Body Electrical > HL AutoLeveling (Sub) > Data List
Tester Display
Front Window Washer Switch
50003 414 1
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

3.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
a.

Remove the headlight cleaner motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL


b.

Inspect the headlight cleaner motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT HEADLIGHT CLEANER CONTROL RELAY ASSEMBLY (H-LP CLN)

NG

REPLACE HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

4.INSPECT HEADLIGHT CLEANER CONTROL RELAY ASSEMBLY (H-LP CLN)
a.

Remove the headlight cleaner control relay assembly (H-LP CLN) from the No. 2 engine room relay block assembly.


b.

Inspect the headlight cleaner control relay assembly (H-LP CLN).

Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY ASSEMBLY (H-LP CLN) AND BATTERY)

NG

REPLACE HEADLIGHT CLEANER CONTROL RELAY ASSEMBLY (H-LP CLN)

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY ASSEMBLY (H-LP CLN) AND BATTERY)
a.

Disconnect the A10 headlight cleaner motor and pump assembly connector.


b.

Remove the headlight cleaner control relay assembly (H-LP CLN) from the No. 2 engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A10-1 - Headlight cleaner control relay assembly (H-LP CLN) terminal 3 Always Below 1 Ω
A10-1 or Headlight cleaner control relay assembly (H-LP CLN) terminal 3 - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A10-2 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY ASSEMBLY (H-LP CLN) - HEADLIGHT ECU SUB-ASSEMBLY RH, BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY ASSEMBLY (H-LP CLN) - HEADLIGHT ECU SUB-ASSEMBLY RH, BATTERY AND BODY GROUND)
a.

Remove the headlight cleaner control relay assembly (H-LP CLN) from the No. 2 engine room relay block assembly.


b.

Disconnect the A12 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight cleaner control relay assembly (H-LP CLN) terminal 2 - A12-7 (HLC) Always Below 1 Ω
Headlight cleaner control relay assembly (H-LP CLN) terminal 5 - Body ground Always Below 1 Ω
Headlight cleaner control relay assembly (H-LP CLN) terminal 5 or A12-7 (HLC) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Headlight cleaner control relay assembly (H-LP CLN) terminal 1 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR