Home › Drivetrain › K120F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076273 K120F MULTIDRIVE / CVT _0372182 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P070312  Brake Switch "B" Circuit Short to Battery  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling when the brakes are suddenly applied while driving with lock-up on.

When the brake pedal is depressed, the stop light switch assembly sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070312 Brake Switch "B" Circuit Short to Battery All of the following conditions are met (2-trip detection logic):
·

The ignition switch is ON.

·

The battery voltage is 8 V or more.

·

The stop light switch assembly remains ON while the vehicle is driven in a GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (2 mph)) pattern 5 times.


·

Short in stop light switch assembly circuit

·

Stop light switch assembly

·

TCM


Comes on DTC stored SAE Code:
P0724

MONITOR DESCRIPTION

This DTC indicates that the stop light switch assembly is remaining on. When the stop light switch assembly remains on during "stop and go" driving, the TCM interprets this as a malfunction of the stop light switch assembly, illuminates the MIL and stores this DTC. The vehicle must STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) five times for two consecutive driving cycles in order to store this DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Repeat the following procedure 5 times:

-

Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to less than 3 km/h (2 mph).


8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P070312.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C403374E01
5.594,2.604 6.052,2.802 0.458,0.198 10 false C33 5.583,2.781 6.042,2.979 0.458,0.198 10 false TCM 5.365,0.99 5.823,1.188 0.458,0.198 10 false STP 5.052,0.99 5.365,1.188 0.313,0.198 10 false 34 4.323,1.125 4.479,1.323 0.156,0.198 10 false L 3.719,1.115 3.875,1.313 0.156,0.198 10 false B 4.563,0.99 4.719,1.188 0.156,0.198 10 false 3 3.458,1 3.615,1.198 0.156,0.198 10 false 7 3.49,1.51 3.948,1.708 0.458,0.198 10 false A40 3.49,1.708 4.625,2.24 1.135,0.531 10 false Stop Light Switch Assembly 2.688,1.313 3.302,1.51 0.615,0.198 10 false STOP 1.698,1.292 2.469,1.49 0.771,0.198 10 false J/B-B 1.281,2.104 2.354,2.302 1.073,0.198 10 false Battery

CAUTION / NOTICE / HINT

CAUTION:
·
A371909

Strictly observe posted speed, limits, traffic laws and road conditions.

·

Do not drive the vehicle with the cable of the GTS contacting the pedals, shift lever or steering wheel.

·

Driving the vehicle with the cable of the GTS contacting these areas could impede vehicle control, resulting in a serious accident.


·
A356953

Do not operate the GTS while driving the vehicle.

·

Operating the GTS while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.



NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List / Stop Light SW.


e.

According to the display on the GTS, read the Data List while the vehicle is being driven.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly status OFF or ON
·

OFF: Brake pedal released

·

ON: Brake pedal depressed


-
Powertrain > Transmission > Data List
Tester Display
Stop Light SW
50003 373 12

OK:

On the GTS screen, ON or OFF is displayed accordingly.


NOTICE:

In the table above, the conditions listed under "Normal Condition" are reference conditions. Do not depend solely on these reference conditions when deciding whether a part is faulty or not.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the stop light switch assembly installation.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

OK:

Stop light switch assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK TERMINAL VOLTAGE (STP VOLTAGE)
a.

Disconnect the TCM connector.

C399498C07
4.865,0.219 5.281,0.469 0.417,0.25 5.76,2.406 6.208,1.396 true 0.667,0.167 0.979,0.323 0.313,0.156 10 false *a 0.688,1.667 1,1.823 0.313,0.156 10 false *b 2.771,0.083 3.083,0.24 0.313,0.156 10 false *c 4.958,0.26 5.417,0.458 0.458,0.198 10 false C33 5.438,2.313 5.896,2.51 0.458,0.198 10 false STP
*a Brake pedal depressed *b Brake pedal released
*c Front view of wire harness connector
(to TCM)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C33-34 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V



HINT:

If there is a short in the STP terminal circuit, there may be a malfunction in the circuit of a connected ECU.


Result:
Proceed to
OK
NG



OK

5.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TCM
a.

Result:
Proceed to
NEXT



NEXT