Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM3620E _53 Suspension _076850 TIRE PRESSURE MONITORING _0374400 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

The switch circuit inside the combination meter assembly turns on and off according to the steering pad switch assembly operation.

During test mode, the tire pressure warning light blinks at 0.125 second intervals when "Set Pressure" is selected on the multi-information display, and illuminates when the "OK" switch (steering pad switch assembly) is pressed.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2198 Initialization Switch (for Test Mode DTC) Test mode procedure is performed.
·

Steering pad switch assembly

·

Spiral cable sub-assembly

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C408663E01
4.521,1.344 7.115,1.563 2.594,0.219 10 false Tire Pressure Warning ECU and Receiver 1.521,2.396 3.406,2.594 1.885,0.198 10 false Combination Meter Assembly 3.302,4.208 5,4.417 1.698,0.208 10 false Spiral Cable Sub-assembly 5.125,4.208 7.052,4.438 1.927,0.229 10 false Steering Pad Switch Assembly 4.865,0.604 5.479,0.802 0.615,0.198 10 false CLSW 1.625,1.01 1.979,1.208 0.354,0.198 10 false G18 1.635,1.573 1.99,1.771 0.354,0.198 10 false G18 1.635,1.969 1.99,2.167 0.354,0.198 10 false G18 3.427,0.594 3.781,0.792 0.354,0.198 10 false G19 3.458,3.021 3.813,3.219 0.354,0.198 10 false G20 4.906,3.021 5.26,3.219 0.354,0.198 10 false z6 4.917,3.427 5.271,3.625 0.354,0.198 10 false z6 4.927,3.833 5.281,4.031 0.354,0.198 10 false z6 3.458,3.448 3.813,3.646 0.354,0.198 10 false G20 3.458,3.844 3.813,4.042 0.354,0.198 10 false G20 3.844,2.958 4.198,3.156 0.354,0.198 10 false +DP 3.844,3.344 4.281,3.563 0.438,0.219 10 false +DP2 3.854,3.74 4.208,3.938 0.354,0.198 10 false EAU 5.26,3.021 5.615,3.219 0.354,0.198 10 false +DP 5.271,3.438 5.708,3.656 0.438,0.219 10 false +DP2 5.281,3.833 5.635,4.031 0.354,0.198 10 false EAU 1.698,0.813 2.01,1.01 0.313,0.198 10 false 23 1.688,1.375 2,1.573 0.313,0.198 10 false 15 1.688,1.771 2,1.969 0.313,0.198 10 false 32 3.479,0.385 3.792,0.583 0.313,0.198 10 false 24 4.667,0.49 4.979,0.688 0.313,0.198 10 false 3 3.5,2.833 3.813,3.031 0.313,0.198 10 false 11 3.51,3.25 3.823,3.448 0.313,0.198 10 false 10 3.552,3.667 3.865,3.865 0.313,0.198 10 false 4 4.938,2.844 5.25,3.042 0.313,0.198 10 false 4 4.948,3.25 5.26,3.448 0.313,0.198 10 false 5 4.917,3.646 5.229,3.844 0.313,0.198 10 false 10 4.531,1.167 4.844,1.365 0.313,0.198 10 false M8 3.104,0.583 3.563,0.781 0.458,0.198 10 false INT 2.01,1.031 2.469,1.229 0.458,0.198 10 false ES 2.01,1.563 2.469,1.76 0.458,0.198 10 false MSTI 2.021,1.958 2.573,2.156 0.552,0.198 10 false MSM+

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G20 spiral cable sub-assembly connector.


b.

Disconnect the G18 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G20-11 (+DP) - G18-32 (MSM+) Always Below 1 Ω
G20-11 (+DP) or G18-32 (MSM+) - Body ground Always 10 kΩ or higher
G20-10 (+DP2) - G18-15 (MSTI) Always Below 1 Ω
G20-10 (+DP2) or G18-15 (MSTI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the M8 tire pressure warning ECU and receiver connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-3 (CLSW) - G19-24 (INT) Always Below 1 Ω
M8-3 (CLSW) or G19-24 (INT) - Body ground Always 10 kΩ or higher
G18-23 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (INT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (INT)
a.

Connect the M8 tire pressure warning ECU and receiver connector.


b.
C406366C07
1.5,0.125 1.885,0.385 0.385,0.26 0.75,1.427 0.917,1.917 0.917,1.917 1.083,1.917 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.896,0.344 0.313,0.156 10 false G19 1.146,1.844 1.646,2.073 0.5,0.229 10 false INT
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G19-24 (INT) - Body ground Ignition switch ON 8 to 15 V


Result:
Proceed to
OK
NG




OK

NG

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER