Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370280 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15C0  GPS Antenna Connection Malfunction(short)  B15C1  GPS Antenna Connection Malfunction(break)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly*1 or No. 1 Amplifier Antenna Assembly*2.

*1: w/o GPS Antenna Divider

*2: w/ GPS Antenna Divider


DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Connection Malfunction(short) Navigation antenna malfunction
w/o GPS Antenna Divider
·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

Radio and Display Receiver Assembly


w/ GPS Antenna Divider
·

Antenna divider

·

Antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

No. 4 antenna cord sub-assembly

·

No. 1 amplifier antenna assembly

·

Radio and Display Receiver Assembly


B15C1 GPS Antenna Connection Malfunction(break) Navigation antenna power source malfunction
w/o GPS Antenna Divider
·

Navigation antenna assembly

·

Antenna cord sub-assembly

·

Radio and Display Receiver Assembly


w/ GPS Antenna Divider
·

Antenna divider

·

Antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

No. 4 antenna cord sub-assembly

·

No. 1 amplifier antenna assembly

·

Radio and Display Receiver Assembly



WIRING DIAGRAM

E402694E03
5.615,1.771 6.906,2.302 1.292,0.531 10 false Radio and Display Receiver Assembly 3.219,1.833 5.625,2.063 2.406,0.229 10 false Antenna Cord Sub-assembly 1.552,1.635 2.823,2.167 1.271,0.531 10 false Navigation Antenna Assembly 5.323,0.885 5.542,1.073 0.219,0.188 10 false B 5.323,1.313 5.542,1.5 0.219,0.188 10 false B 5.313,0.635 5.521,0.844 0.208,0.208 10 false 1 5.281,1.104 5.573,1.292 0.292,0.188 10 false 1a 3,1.313 3.219,1.5 0.219,0.188 10 false A 3,0.896 3.219,1.083 0.219,0.188 10 false A 2.99,0.667 3.198,0.875 0.208,0.208 10 false 3 2.969,1.094 3.177,1.302 0.208,0.208 10 false 3a 5.604,0.906 6.896,1.438 1.292,0.531 10 false GPS 0.063,0.094 2.177,0.385 2.115,0.292 12 false w/o GPS Antenna Divider: 5.635,1.302 6.927,1.833 1.292,0.531 10 false GND

E402724E01
0.063,0.052 4.281,0.292 4.219,0.24 12 false w/ GPS Antenna Divider: 5.698,1.99 6.938,2.458 1.24,0.469 10 false Radio and Display Receiver Assembly 5.427,3.052 5.771,3.323 0.344,0.271 10 false E 5.771,0.802 6.125,1.052 0.354,0.25 10 false GPS 5.781,1.271 6.135,1.521 0.354,0.25 10 false GND 4.208,4.958 5.448,5.396 1.24,0.438 10 false Antenna Cord Sub-assembly 5.677,4.74 6.906,5.167 1.229,0.427 10 false Antenna Divider 1.354,4.896 2.594,5.313 1.24,0.417 10 false No. 4 Antenna Cord Sub-assembly 2.719,4.729 3.927,5.146 1.208,0.417 10 false No. 1 Amplifier Antenna Assembly 2.49,4.031 2.698,4.219 0.208,0.188 10 false A 2.479,0.813 2.688,1 0.208,0.188 10 false B 2.49,1.604 2.698,1.792 0.208,0.188 10 false B 2.49,3.583 2.698,3.771 0.208,0.188 10 false A 4,0.813 4.208,1 0.208,0.188 10 false D 4.01,1.615 4.219,1.802 0.208,0.188 10 false D 5.427,1.281 5.76,1.552 0.333,0.271 10 false F 2.698,2.385 3.927,2.813 1.229,0.427 10 false No. 3 Antenna Cord Sub-assembly 5.427,0.594 5.771,0.865 0.344,0.271 10 false 1 5.396,1.073 5.74,1.344 0.344,0.271 10 false 1a 3.958,0.396 4.302,0.667 0.344,0.271 10 false 5*1 3.896,1.208 4.24,1.479 0.344,0.271 10 false 5a*1 2.458,1.354 2.802,1.625 0.344,0.271 10 false 1a 2.5,0.594 2.844,0.865 0.344,0.271 10 false 1 2.49,3.344 2.833,3.615 0.344,0.271 10 false 5 2.448,3.823 2.792,4.094 0.344,0.271 10 false 5a 5.417,3.542 5.75,3.813 0.333,0.271 10 false E 5.448,0.813 5.781,1.083 0.333,0.271 10 false F 5.427,4.01 5.76,4.281 0.333,0.271 10 false E 5.427,4.479 5.76,4.75 0.333,0.271 10 false E 5.438,2.854 5.781,3.125 0.344,0.271 10 false 2 5.406,3.344 5.75,3.615 0.344,0.271 10 false 2a 5.427,3.813 5.771,4.083 0.344,0.271 10 false 6 5.396,4.26 5.74,4.531 0.344,0.271 10 false 6a 3.948,0.615 4.292,0.885 0.344,0.271 10 false 1*2 3.885,1.406 4.229,1.677 0.344,0.271 10 false 1a*2 0,5.167 1.604,5.5 1.604,0.333 10 false *1: w/o DAB Function 0,5.479 1.604,5.813 1.604,0.333 10 false *2: w/ DAB Function

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.


·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



HINT:

When inspect the Antenna Cord Sub-assembly, check if the Antenna Divider is equipped.

Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK MODEL
2.CHECK MODEL
a.

Choose the model to be inspected.

i.

Remove the antenna cord sub-assembly, check if the antenna divider is equipped.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL



Result:
Result Proceed to
w/o GPS Antenna Divider A
w/ GPS Antenna Divider B



A

3.INSPECT ANTENNA CORD SUB-ASSEMBLY

B

5.CHECK MODEL
3.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E322997C12
0.5,1.188 0.917,1.438 0.417,0.25 0.656,3.479 1.073,3.729 0.417,0.25 1.927,3.76 2.344,3.344 true 1.854,1 2.271,0.583 true 1.229,4.135 1.646,3.854 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 2.354,3.177 3.167,3.417 0.813,0.24 10 false 1a (GND) 2.313,0.427 2.625,0.625 0.313,0.198 10 false 3a 0.656,1.24 0.969,1.438 0.313,0.198 10 false A 0.823,3.531 1.135,3.729 0.313,0.198 10 false B 0.135,2.542 0.448,2.74 0.313,0.198 10 false *b 0.844,4.052 1.333,4.25 0.49,0.198 10 false GPS
*a Front view of wire harness connector
(to Navigation Antenna Assembly)
*b Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the antenna connector from the radio and display receiver assembly.


b.

Disconnect the antenna connector from the navigation antenna assembly.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - B-1 (GPS) Always Below 1 Ω
A-3a - B-1a (GND) Always Below 1 Ω
A-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NAVIGATION ANTENNA ASSEMBLY

NG

4.INSPECT NAVIGATION ANTENNA ASSEMBLY


Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

5.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/o DAB Function A
w/ DAB Function B




A

6.INSPECT ANTENNA CORD SUB-ASSEMBLY

B

11.INSPECT ANTENNA CORD SUB-ASSEMBLY
6.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E402725C01
1.521,0.115 1.885,0.354 0.365,0.24 1.583,2.875 1.948,3.115 0.365,0.24 1.531,1.385 1.896,1.625 0.365,0.24 1.198,1.167 1.365,1.167 1.365,1.167 1.635,0.99 true 1.01,1.656 1.177,1.656 1.177,1.656 1.292,2.229 true 2.719,1.656 2.552,1.656 2.552,1.656 2.49,2.219 true 1.177,3.188 1.344,3.188 1.344,3.188 1.458,3.76 true 1.75,0.885 2.125,1.135 2.125,1.135 2.292,1.135 true 1.677,0.167 1.833,0.365 0.156,0.198 10 false F 0.083,0.115 0.615,0.313 0.531,0.198 10 false *a 0.104,1.26 0.635,1.458 0.531,0.198 10 false *b 0.094,2.813 0.625,3.01 0.531,0.198 10 false *c 1.667,1.427 1.823,1.625 0.156,0.198 10 false E 1.708,2.917 1.865,3.115 0.156,0.198 10 false D 0.573,1.073 1.365,1.292 0.792,0.219 10 false 1a (GND) 0.823,1.573 1.094,1.792 0.271,0.219 10 false 2a 2.771,1.573 3.042,1.792 0.271,0.219 10 false 6a 0.99,3.094 1.26,3.313 0.271,0.219 10 false 5a 2.344,1.031 3.135,1.25 0.792,0.219 10 false GPS
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Antenna Divider)
*c Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the radio and display receiver assembly.


b.

Disconnect the antenna connector from the antenna divider.


c.

Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F-1- E-2 Always Below 1 Ω
F-1a - E-2a Always Below 1 Ω
E-6 - D-5 Always Below 1 Ω
E-6a - D-5a Always Below 1 Ω
F-1 - Body ground Always 10 kΩ or higher
E-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT ANTENNA DIVIDER

NG

7.INSPECT ANTENNA DIVIDER
a.

b.
E402726C01
1.375,1.417 1.229,1.76 1.229,1.76 1.031,1.76 true 2.271,1.406 2.125,1.75 2.125,1.75 1.927,1.75 true 0.844,1.677 1.271,1.854 0.427,0.177 10 false 2a 1.75,1.656 2.177,1.833 0.427,0.177 10 false 6a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 - 2 Always 10 kΩ or higher
2 - 2a Always 243 to 267 Ω
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

8.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E369779C04
1.51,0.188 1.938,0.448 0.427,0.26 1.552,1.75 1.979,2.01 0.427,0.26 2.323,0.969 2.5,0.24 2.5,0.24 2.719,0.24 true 0.792,2.583 0.552,1.938 0.552,1.938 0.365,1.938 true 1.677,0.229 1.833,0.427 0.156,0.198 10 false D 0.146,0.094 0.302,0.292 0.156,0.198 10 false *a 0.073,1.552 0.229,1.75 0.156,0.198 10 false *b 1.708,1.802 1.865,2 0.156,0.198 10 false B 2.771,0.167 3.135,0.448 0.365,0.281 10 false 5a 0.177,1.844 0.385,2.094 0.208,0.25 10 false 1a
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-5 - B-1 Always Below 1 Ω
D-5a - B-1a Always Below 1 Ω
D-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG

9.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E408070C02
1.469,0.313 1.917,0.552 0.448,0.24 0.323,2.979 0.771,3.219 0.448,0.24 2.542,1.24 2.688,0.427 2.688,0.427 2.875,0.427 true 1.865,3.281 2.469,3.781 2.469,3.781 2.646,3.781 true 1.656,0.344 1.813,0.542 0.156,0.198 10 false B 0.49,3.021 0.646,3.219 0.156,0.198 10 false A 0.073,0.073 0.333,0.271 0.26,0.198 10 false *a 0.125,2.156 0.385,2.354 0.26,0.198 10 false *b 2.948,0.323 3.26,0.531 0.313,0.208 10 false 1a 2.698,3.688 3.01,3.896 0.313,0.208 10 false 5a
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 1 amplifier antenna assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - A-5 Always Below 1 Ω
B-1a - A-5a Always Below 1 Ω
B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY

NG

10.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the No. 1 amplifier antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

11.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E402725C03
1.521,0.115 1.885,0.354 0.365,0.24 1.583,2.875 1.948,3.115 0.365,0.24 1.531,1.385 1.896,1.625 0.365,0.24 1.198,1.167 1.365,1.167 1.365,1.167 1.635,0.99 true 1.01,1.656 1.177,1.656 1.177,1.656 1.292,2.229 true 2.719,1.656 2.552,1.656 2.552,1.656 2.49,2.219 true 2.656,3.219 2.49,3.219 2.49,3.219 2.427,3.781 true 1.75,0.906 1.979,1.146 1.979,1.146 2.26,1.146 true 1.677,0.167 1.833,0.365 0.156,0.198 10 false F 0.083,0.115 0.615,0.313 0.531,0.198 10 false *a 0.104,1.26 0.635,1.458 0.531,0.198 10 false *b 0.094,2.813 0.625,3.01 0.531,0.198 10 false *c 1.667,1.427 1.823,1.625 0.156,0.198 10 false E 1.708,2.917 1.865,3.115 0.156,0.198 10 false D 0.583,1.073 1.323,1.323 0.74,0.25 10 false 1a (GND) 0.823,1.573 1.094,1.792 0.271,0.219 10 false 2a 2.771,1.573 3.042,1.792 0.271,0.219 10 false 6a 2.75,3.146 3.021,3.365 0.271,0.219 10 false 1a 2.323,1.063 3.063,1.313 0.74,0.25 10 false GPS
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Antenna Divider)
*c Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the radio and display receiver assembly.


b.

Disconnect the antenna connector from the antenna divider.


c.

Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F-1 - E-2 Always Below 1 Ω
F-1a - E-2a Always Below 1 Ω
E-6 - D-1 Always Below 1 Ω
E-6a - D-1a Always Below 1 Ω
F-1 - Body ground Always 10 kΩ or higher
E-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT ANTENNA DIVIDER

NG

12.INSPECT ANTENNA DIVIDER

b.
E402726C01
1.375,1.417 1.229,1.76 1.229,1.76 1.031,1.76 true 2.271,1.406 2.125,1.75 2.125,1.75 1.927,1.75 true 0.844,1.677 1.271,1.854 0.427,0.177 10 false 2a 1.75,1.656 2.177,1.833 0.427,0.177 10 false 6a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 - 2 Always Below 1 Ω
6 - 2a Always Below 1 Ω
6 - 6a Always 10 kΩ or higher
2 - 2a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

13.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E369779C05
1.51,0.188 1.938,0.448 0.427,0.26 1.552,1.75 1.979,2.01 0.427,0.26 0.792,2.583 0.552,1.938 0.552,1.938 0.365,1.938 true 0.781,0.969 0.542,0.469 0.542,0.469 0.354,0.469 true 1.677,0.229 1.833,0.427 0.156,0.198 10 false D 0.146,0.094 0.302,0.292 0.156,0.198 10 false *a 0.073,1.552 0.229,1.75 0.156,0.198 10 false *b 1.708,1.802 1.865,2 0.156,0.198 10 false B 0.177,1.844 0.385,2.094 0.208,0.25 10 false 1a 0.156,0.375 0.396,0.583 0.24,0.208 10 false 1a
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-1 - B-1 Always Below 1 Ω
D-1a - B-1a Always Below 1 Ω
D-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG