Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SRS SEAT CUSHION AIRBAG ASSEMBLY
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0374452 SRS SEAT CUSHION AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  SRS SEAT CUSHION AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

·

If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

B401137



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the horn button assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 739F0 2.DISPOSE OF FRONT SEAT CUSHION AIRBAG ASSEMBLY RH (When Installed to Vehicle)

NOTICE:
·

When disposing of the front seat cushion airbag assembly RH, use an unneeded vehicle to deploy the airbag.

·

Be sure to perform the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

for HV Model:

i.

Remove the deck board assembly.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL


ii.

Remove the rear No. 2 floor board.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL


iii.

Remove the battery hole cover.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL



d.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




e.

Remove the 4 bolts and tilt the front seat assembly RH backward.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL


f.

Install SST.

i.
B523159N01
1.875,1.875 1.875,0.823 1.875,0.823 2.813,0.823 true 2.365,1.313 2.365,0.823 true 2.865,0.719 3.208,0.906 0.344,0.188 10 true SST

Connect SST to the front seat airbag assembly RH.

SST
09082-00750  

CAUTION:
B524513

·

Do not deploy if the front seat cushion airbag assembly RH is loose.

·

If deployed while the front seat cushion airbag assembly RH is loose, the front seat cushion airbag assembly RH may fly off and cause serious injuries.




ii.

Connect SST together (09082-00700 and 09082-00750).

NOTICE:

To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.



iii.

Return the front seat assembly RH to its original position.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION

CAUTION:
B434268

Check that there is no looseness in the front seat assembly RH.




g.

Deploy the airbag.

i.
C154370C53
0.458,1.167 0.677,1.167 false 0.677,1.167 0.927,1.396 false 1.594,1.802 1.906,1.958 0.313,0.156 10 false *a 0.177,1.104 0.573,1.323 0.396,0.219 10 false SST
*a 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


ii.

While maintaining sufficient clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.

CAUTION:
B394904

·

Do not deploy with all the doors and door windows open.

·

If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.



NOTICE:

Take care not to damage SST wire harness.



iii.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


v.

Press SST activation switch to deploy the airbag.

CAUTION:
B400936

·

Do not deploy with people inside or around the vehicle.

·

If deployed with people inside or around the vehicle, serious injuries may occur.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




h.

Remove the front seat cushion airbag assembly RH.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SRS SEAT CUSHION AIRBAG ASSEMBLY>REMOVAL

CAUTION:
·
B434269

The front seat cushion airbag assembly RH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B434271

Do not apply water etc. to a front seat cushion airbag assembly RH with a deployed airbag.

·

If water is applied to the front seat cushion airbag assembly RH immediately after deployment, burns may occur from the resulting steam.

·
B434270

Always wear safety glasses and gloves when handling a deployed front seat cushion airbag assembly RH.

·

If the front seat cushion airbag assembly RH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·

After removal, quickly seal the front seat cushion airbag assembly RH in a plastic bag.




i.

Dispose of the front seat cushion airbag assembly RH.

i.

Place the front seat cushion airbag assembly RH in a plastic bag, tie it tightly and dispose of it according to local regulations.

CAUTION:
·
B428378

The front seat cushion airbag assembly RH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B428379

Do not apply water etc. to a front seat cushion airbag assembly RH with a deployed airbag.

·

If water is applied to the front seat cushion airbag assembly RH immediately after deployment, burns may occur from the resulting steam.

·
B428380

Always wear safety glasses and gloves when handling a deployed front seat cushion airbag assembly RH.

·

If the front seat cushion airbag assembly RH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B428377

Never dispose of a front seat cushion airbag assembly RH with an undeployed airbag.

·

If an undeployed front seat cushion airbag assembly RH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.





Hide 739F0 3.DISPOSE OF FRONT SEAT CUSHION AIRBAG ASSEMBLY RH (When not Installed to Vehicle)

NOTICE:

Be sure to perform the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

for HV Model:

i.

Remove the deck board assembly.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL


ii.

Remove the rear No. 2 floor board.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL


iii.

Remove the battery hole cover.

Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL



d.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




e.

Remove the front seat cushion airbag assembly RH.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SRS SEAT CUSHION AIRBAG ASSEMBLY>REMOVAL


f.

Install SST.

i.
B524514N01
1.729,1.906 1.354,1.656 false 1.792,1.833 2.25,2.031 0.458,0.198 10 false SST

Connect SST to the front seat cushion airbag assembly RH.

SST
09082-00750  



g.
B104882C91
2.854,0.99 3.094,1.167 0.24,0.177 10 false *a
*a Wire Diameter
V100155

Stripped Wire


Using braided wire, tie down the front seat cushion airbag assembly RH to an unneeded tire.

Wire:

Cross-sectional area of stripped wire

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the front seat cushion airbag assembly RH, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the cross-sectional area of stripped wire:

Area = 3.14 x (Diameter)2 / 4


i.
B523160

Install the 2 nuts to the front seat cushion airbag assembly RH.


ii.
B523161

Wind 2 or more wires around the stud bolts of the front seat cushion airbag assembly RH as shown in the illustration.


iii.
B523162C01
2.792,0.656 1.823,0.771 true 2.073,0.052 2.385,0.208 0.313,0.156 10 false *a 0.823,1 1.135,1.156 0.313,0.156 10 false *b 2.844,0.563 3.156,0.719 0.313,0.156 10 false *c
*a Width
*b Inner Diameter
*c Deployment Side


Position the front seat cushion airbag assembly RH inside the tire with the airbag deployment side facing upward.

Minimum tire size:

Must exceed the following dimensions

Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
B467376C02
2.156,1.844 2.708,1.938 true 2.771,1.865 3.083,2.021 0.313,0.156 10 false *a
*a Remove looseness
V100155

Deployment Side


·

Do not install the front seat cushion airbag assembly RH with the airbag deployment side facing inside.

·

When securing the front seat cushion airbag assembly RH, make sure there is no looseness in the wire harness.

·

If installed with the airbag deployment side facing inside or the wire harness is loosely wrapped, the deployed front seat cushion airbag assembly RH and tire may fly off and cause serious injuries.



NOTICE:

The tire may be damaged by the airbag deployment, so use an unneeded tire.




h.

Place the tires.

i.
B523164C01
2.219,0.542 2.615,0.542 true 2.198,1.823 2.5,1.823 2.5,1.823 2.5,0.542 true 2.25,0.781 2.49,0.781 true 2.24,1.417 2.49,1.417 true 2.667,0.448 2.979,0.604 0.313,0.156 10 false *a
*a Tires (2 or more)


Place at least 2 tires under the tire to which the front seat cushion airbag assembly RH is tied.


ii.

Place at least 2 tires onto the tire to which the front seat cushion airbag assembly RH is tied. The top tire should have a wheel installed.

NOTICE:
·

Do not place SST connector under the tire because it could be damaged.

·

The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.




iii.
C223306

Tie the tires together with 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.




i.

Install SST.

i.
B523165C01
1.323,2.417 1.479,0.563 false 1.146,0.552 1.479,0.552 1.479,0.552 1.896,2.417 true 1.479,2.719 1.792,2.875 0.313,0.156 10 false *a 0.813,0.458 1.281,0.656 0.469,0.198 10 false SST
*a 10 m (32.8 ft.) or more


Connect SST together (09082-00700 and 09082-00750).

SST
09082-00700  

NOTICE:

To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.



ii.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tires.



j.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the front seat cushion airbag assembly RH is tied.


iii.

Press SST activation switch to deploy the airbag.

CAUTION:
B401768

·

Do not deploy with people around the tire.

·

If deployed with people around the tire, serious injuries may occur.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




k.

Dispose of the front seat cushion airbag assembly RH.

CAUTION:
·
B428378

The front seat cushion airbag assembly RH becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B428379

Do not apply water etc. to a front seat cushion airbag assembly RH with a deployed airbag.

·

If water is applied to the front seat cushion airbag assembly RH immediately after deployment, burns may occur from the resulting steam.

·
B428380

Always wear safety glasses and gloves when handling a deployed front seat cushion airbag assembly RH.

·

If the front seat cushion airbag assembly RH is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B428377

Never dispose of a front seat cushion airbag assembly RH with an undeployed airbag.

·

If an undeployed front seat cushion airbag assembly RH is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.



i.

Remove the front seat cushion airbag assembly RH from the tire.


ii.

Place the front seat cushion airbag assembly RH in a plastic bag, tie it tightly, and dispose of it according to local regulations.