Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat) › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076405 SEAT _0372016 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·
B521791

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SEAT ASSEMBLY LH

a.
B521500

Place the front seat assembly LH in the vehicle as shown in the illustration.

NOTICE:
·

2 or more people are required when reinstalling the front seat assembly LH into the vehicle.

·

Protect the front seat leg.

·

Be careful not to damage the front seat assembly LH, body exterior or interior parts.




b.

Tilt the front seat assembly LH backward.

NOTICE:

Be careful not to damage the front seat assembly LH or interior parts.



c.

Connect the front seat airbag assembly LH connector.

B529785C03
3.594,0.104 3.906,0.323 0.313,0.219 12 false *A 0.302,0.104 0.615,0.323 0.313,0.219 12 false *B 6.135,0.542 6.406,0.75 0.271,0.208 12 true *C 0.781,0.479 1.042,0.688 0.26,0.208 12 true *D 1.573,0.188 1.833,0.396 0.26,0.208 12 true *E
*A for Driver Side *B for Front Passenger Side
*C w/ Seat Heater System *D w/ Seat Heater System or w/ Climate Control Seat System
*E w/ Occupant Classification System - -
V100136

Front Seat Airbag Assembly Connector
V100137

Front Seat Cushion Airbag Assembly RH Connector


i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B345877C01
3.01,2.594 3.01,2.656 3.01,2.656 3.448,2.656 false 3,1.229 3,1.292 3,1.292 3.438,1.292 false 6.104,0.948 6.104,1.167 6.104,1.167 6.302,1.167 false 6.135,2.375 6.135,2.594 6.135,2.594 6.333,2.594 false 0.969,0.708 1.281,0.906 0.313,0.198 10 false *a 4.448,0.708 4.76,0.906 0.313,0.198 10 false *a 0.969,2.052 1.281,2.25 0.313,0.198 10 false *b 4.458,2.052 4.771,2.25 0.313,0.198 10 false *b 3.521,1.198 3.833,1.396 0.313,0.198 10 false *c 6.375,1.083 6.688,1.281 0.313,0.198 10 false *c 6.396,2.5 6.708,2.698 0.313,0.198 10 false *c 3.51,2.552 3.896,2.698 0.385,0.146 10 false *c
*a Correct *b Incorrect
*c Yellow CPA - -



ii.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

NOTICE:
·

Be careful not to damage the connector or wire harness of the front seat airbag assembly LH.

·

When connecting the connector, make sure to push it straight in.

·

Do not hold any parts other than the yellow CPA when connecting the connector.

·

If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.





d.

for Front Passenger Side, w/ Occupant Classification System:

Connect the front seat cushion airbag assembly RH connector.

NOTICE:
·

Be careful not to damage the connector or wire harness of the front seat cushion airbag assembly RH.

·

When connecting the connector, make sure to push it straight in.




e.

Connect each connector and attach the clamp under the front seat assembly LH.


f.

Temporarily install the front seat assembly LH with the 4 "TORX" screws.


g.

Operate the seat track adjusting handle and move the front seat assembly LH to the rearmost position.


h.
B521497N01
0.156,0.219 0.365,0.417 0.208,0.198 10 true (1) 0.99,1.385 1.198,1.583 0.208,0.198 10 true (2)

Using a T50 "TORX" socket wrench, tighten the 2 "TORX" screws in the order shown in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


i.

Operate the seat track adjusting handle and move the front seat assembly LH to the frontmost position.


j.
B521498N01
2.854,0.375 3.052,0.573 0.198,0.198 10 true (1) 0.479,0.958 0.677,1.156 0.198,0.198 10 true (2)

Using a T50 "TORX" socket wrench, tighten the 2 "TORX" screws in the order shown in the illustration.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 72138N 2.INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH

a.
B521463C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the rear outer seat track bracket cover LH as shown in the illustration.


Hide 72158E 3.INSTALL REAR INNER SEAT TRACK BRACKET COVER LH

a.
B521465C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the rear inner seat track bracket cover LH as shown in the illustration.


Hide 72124 4.INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH

a.

Operate the seat track adjusting handle and move the front seat assembly LH to the frontmost position.


b.
B521461C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the front outer seat track bracket cover LH as shown in the illustration.


Hide 72124A 5.INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH

HINT:

Use the same procedure described for the front outer seat track bracket cover LH.


Hide 71910A 6.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.

Install the front seat headrest assembly to the front seat assembly LH.


Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 8.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 9.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 10.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 11. PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK (for Front Passenger Seat, w/ Occupant Classification System)

Hide 12.INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)

Hide 13.INSPECT CLIMATE CONTROL SEAT SYSTEM (w/ Climate Control Seat System)