Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370280 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B157D  DAB Tuner Antenna Disconnected  


DESCRIPTION

This DTC is stored when a malfunction occurs in the DAB tuner antenna which is connected to the radio and display receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157D DAB Tuner Antenna Disconnected The DAB tuner antenna is not connected
·

Back Door Glass (DAB Antenna)

·

No. 5 antenna cord sub-assembly

·

No. 4 antenna cord sub-assembly

·

No. 3 Antenna cord sub-assembly

·

Antenna cord sub-assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E369780E03
0.052,2.906 1.615,3.469 1.563,0.563 10 false Back Door Glass (DAB Antenna) 0.958,2.115 2.25,2.594 1.292,0.479 10 false No. 5 Antenna Cord Sub-assembly 2.313,2.125 3.552,2.49 1.24,0.365 10 false No. 4 Antenna Cord Sub-assembly 3.354,3.104 4.583,3.469 1.229,0.365 10 false No. 3 Antenna Cord Sub-assembly 4.74,3.115 5.948,3.656 1.208,0.542 10 false Antenna Cord Sub-assembly 5.885,3.885 7.135,4.323 1.25,0.438 10 false Radio and Display Receiver Assembly 6.073,0.365 6.635,0.708 0.563,0.344 10 false DAB 1.021,0.396 1.219,0.563 0.198,0.167 10 false A 1.021,1.51 1.219,1.677 0.198,0.167 10 false A 1.021,0.188 1.219,0.354 0.198,0.167 10 false 1 0.979,1.302 1.177,1.469 0.198,0.167 10 false 1a 2.146,0.396 2.344,0.563 0.198,0.167 10 false B 2.146,0.188 2.344,0.354 0.198,0.167 10 false 1 2.104,1.302 2.302,1.469 0.198,0.167 10 false 1a 2.146,1.521 2.344,1.688 0.198,0.167 10 false B 3.375,0.396 3.573,0.563 0.198,0.167 10 false C 3.396,0.198 3.594,0.365 0.198,0.167 10 false 5 3.375,1.521 3.573,1.688 0.198,0.167 10 false C 3.354,1.302 3.552,1.469 0.198,0.167 10 false 5a 4.552,0.406 4.75,0.573 0.198,0.167 10 false D 4.563,1.521 4.76,1.688 0.198,0.167 10 false D 4.563,0.198 4.76,0.365 0.198,0.167 10 false 5 4.531,1.302 4.729,1.469 0.198,0.167 10 false 5a 5.688,0.396 5.938,0.573 0.25,0.177 10 false DB 5.677,1.521 5.927,1.698 0.25,0.177 10 false DB 5.74,0.188 5.938,0.354 0.198,0.167 10 false 1 5.719,1.313 5.917,1.479 0.198,0.167 10 false 1a 6.042,1.552 6.604,1.896 0.563,0.344 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.



Result:
Proceed to
OK
NG



OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK BACK DOOR GLASS (WINDOW GLASS ANTENNA WIRE)
3.CHECK BACK DOOR GLASS (WINDOW GLASS ANTENNA WIRE)
a.
E111994C29
0.75,1.115 0.594,0.688 true 1.094,1.896 0.979,1.625 true 2.302,1.656 2.188,1.385 true 0.479,0.51 0.656,0.688 0.177,0.177 10 false *a 1.094,1.906 1.271,2.083 0.177,0.177 10 false *b 2.271,1.677 2.448,1.854 0.177,0.177 10 false *c
*a Tester Probe
*b Antenna Wire
*c Tin Foil


Check for continuity in the door glass antenna wire.

HINT:

Check for continuity at the center of each antenna wire as shown in the illustration.


NOTICE:

When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger as shown in the illustration.


OK:

There is continuity in the door glass antenna wire.



Result:
Proceed to
OK
NG



OK

4.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPAIR QUARTER WINDOW ASSEMBLY RH (WINDOW GLASS ANTENNA WIRE)

4.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E402721C01
0.667,0.635 1.083,0.875 0.417,0.24 1.479,1.646 1.896,1.885 0.417,0.24 1.698,1.021 2.063,1.51 2.063,1.51 2.292,1.51 true 1.344,2.552 1.115,1.896 1.115,1.896 0.885,1.896 true 1.719,0.854 2.031,0.51 2.031,0.51 2.26,0.51 true 0.771,0.677 1.083,0.875 0.313,0.198 10 false DB 0.219,0.219 0.531,0.417 0.313,0.198 10 false *a 1.646,1.688 1.958,1.885 0.313,0.198 10 false D 0.208,1.479 0.521,1.677 0.313,0.198 10 false *b 2.344,1.406 3.01,1.667 0.667,0.26 10 false 1a (GND) 0.688,1.802 1,2 0.313,0.198 10 false 5a 2.333,0.385 3,0.646 0.667,0.26 10 false DAB
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the radio and display receiver assembly.


b.

Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DB-1 (DAB) - D-5 Always Below 1 Ω
DB-1a (GND) - D-5a Always Below 1 Ω
DB-1 (DAB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

5.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E369779C03
1.552,0.125 1.896,0.365 0.344,0.24 1.563,1.813 1.906,2.052 0.344,0.24 2.25,1.135 2.573,1.615 2.573,1.615 2.75,1.615 true 2.219,2.792 2.531,3.219 2.531,3.219 2.708,3.219 true 0.271,0.25 0.5,0.448 0.229,0.198 10 false *a 0.281,1.906 0.51,2.104 0.229,0.198 10 false *b 1.677,0.167 1.813,0.344 0.135,0.177 10 false D 1.698,1.844 1.833,2.021 0.135,0.177 10 false C 2.844,1.521 3.073,1.719 0.229,0.198 10 false 5a 2.75,3.135 2.979,3.333 0.229,0.198 10 false 5a
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-5 - C-5 Always Below 1 Ω
D-5a - C-5a Always Below 1 Ω
D-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG

6.CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E402628C03
1.51,0.385 2,0.635 0.49,0.25 1.51,1.917 2,2.167 0.49,0.25 1.083,1.833 1.229,1.833 1.229,1.833 1.396,1.333 true 1.885,2.854 2.271,2.615 2.271,2.615 2.448,2.615 true 1.719,0.438 1.875,0.635 0.156,0.198 10 false C 0.115,0.146 0.354,0.344 0.24,0.198 10 false *a 0.125,1.865 0.365,2.063 0.24,0.198 10 false *b 1.708,1.969 1.865,2.167 0.156,0.198 10 false B 0.896,1.729 1.146,1.938 0.25,0.208 10 false 5a 2.5,2.521 2.75,2.729 0.25,0.208 10 false 1a
*a Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 5 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the No. 5 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-5 - B-1 Always Below 1 Ω
C-5a - B-1a Always Below 1 Ω
C-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 5 ANTENNA CORD SUB-ASSEMBLY

NG

7.CHECK NO. 5 ANTENNA CORD SUB-ASSEMBLY
a.
E402629C02
1.51,0.198 1.885,0.448 0.375,0.25 1.479,1.76 1.854,2.01 0.375,0.25 1.813,1.271 2.094,1.615 2.094,1.615 2.292,1.615 true 1.792,2.854 2.083,3.208 2.083,3.208 2.271,3.208 true 1.667,0.24 1.823,0.438 0.156,0.198 10 false B 1.625,1.802 1.781,2 0.156,0.198 10 false A 2.344,1.531 2.656,1.729 0.313,0.198 10 false 1a 2.323,3.135 2.635,3.333 0.313,0.198 10 false 1a 0.573,0.469 0.802,0.688 0.229,0.219 10 false *a 0.573,2.125 0.802,2.344 0.229,0.219 10 false *b
*a Front view of wire harness connector
(to No. 4 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Back Door Glass [DAB Antenna])


Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.


b.

Disconnect the antenna connector from the back door glass (DAB Antenna).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 - A-1 Always Below 1 Ω
B-1a - A-1a Always Below 1 Ω
B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE BACK DOOR GLASS (DAB ANTENNA)

NG

8.REPLACE BACK DOOR GLASS (DAB ANTENNA)
a.

Replace the back door glass (DAB Antenna) with a new or known good one.

Click hereVehicle Exterior>WINDOW / GLASS>BACK DOOR GLASS>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (BACK DOOR GLASS [DAB ANTENNA] IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY