Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076405 SEAT _0374976 SEAT HEATER SYSTEM J

SEAT  SEAT HEATER SYSTEM  Seat Heater for Rear Right Seat does not Operate  


DESCRIPTION

When the seat heater (rear) switch RH is operated, the air conditioning amplifier assembly receives the signal from the air conditioning control assembly via the LIN communication line and operates the RH side rear seat heater.

WIRING DIAGRAM

E409347E01
0.156,7.552 1.708,7.917 1.552,0.365 10 false Air Conditioning Amplifier Assembly 4.01,6.615 5.667,6.99 1.656,0.375 10 false Seat Heater Assembly RH (Rear Seat Cushion) 5.729,6.625 7.115,6.99 1.385,0.365 10 false Seat Heater Assembly RH (Rear Seatback) 0.708,8.323 2.49,8.5 1.781,0.177 10 false : LIN Communication Line 2.208,2.74 3.667,3.104 1.458,0.365 10 false Air Conditioning Control Assembly 4.5,2.906 6.448,3.083 1.948,0.177 10 false Seat Heater (Rear) Switch RH 4.74,0.573 5.802,0.74 1.063,0.167 10 false ECU-IG1 NO.4 3.063,0.396 4.427,0.583 1.365,0.188 10 false from IG1 NO.1 Relay 6.021,1.448 6.26,1.615 0.24,0.167 10 false IG 4.667,1.448 4.969,1.615 0.302,0.167 10 false IND 4.677,1.896 4.844,2.073 0.167,0.177 10 false E 4.5,2.75 4.719,2.917 0.219,0.167 10 false K3 6.292,1.448 6.427,1.635 0.135,0.188 10 false 5 4.469,1.448 4.667,1.625 0.198,0.177 10 false 4 4.469,1.885 4.667,2.063 0.198,0.177 10 false 2 3.188,1.563 3.583,1.74 0.396,0.177 10 false SWB 3.198,2.01 3.594,2.188 0.396,0.177 10 false SW2 2.208,2.573 2.583,2.75 0.375,0.177 10 false G24 3.625,1.458 3.76,1.646 0.135,0.188 10 false 6 3.635,1.885 3.833,2.063 0.198,0.177 10 false 2 2.427,1.74 2.823,1.917 0.396,0.177 10 false LIN1 0.917,1.75 1.313,1.927 0.396,0.177 10 false LIN1 2.802,3.635 3.542,3.802 0.74,0.167 10 false S-HTR RR 3.99,3.458 5.521,3.656 1.531,0.198 10 false from Auxiliary Battery 2.01,5.938 2.833,6.104 0.823,0.167 10 false S/HTR R/R 3.771,5.167 4.125,5.333 0.354,0.167 10 false N43 3.76,5.781 4.115,5.948 0.354,0.167 10 false N43 4.208,5.031 4.375,5.208 0.167,0.177 10 false B 4.208,5.667 4.375,5.844 0.167,0.177 10 false E 3.854,4.927 4.021,5.104 0.167,0.177 10 false 1 3.854,5.542 4.021,5.719 0.167,0.177 10 false 3 1.917,5.042 2.052,5.219 0.135,0.177 10 false 5 2.719,5.042 2.854,5.219 0.135,0.177 10 false 3 1.906,5.521 2.042,5.698 0.135,0.177 10 false 1 2.729,5.531 2.865,5.708 0.135,0.177 10 false 2 0.844,6.594 1.26,6.771 0.417,0.177 10 false SH2R 0.146,7.375 0.563,7.552 0.417,0.177 10 false G47 1.323,6.469 1.531,6.656 0.208,0.188 10 false 20

CAUTION / NOTICE / HINT

NOTICE:
·

If the auxiliary battery voltage is low, the seat heater system may not operate. When "High Power Consumption Partial Limit on AC/Heater Operation" is displayed on the multi-information display in the combination meter assembly, inspect the auxiliary battery, referring to On-vehicle Inspection for the charging system.

for A25A-FKS: Click herePower Source / Network>A25A-FKS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION

for M20A-FKS: Click herePower Source / Network>M20A-FKS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION

for A25A-FXS: Click herePower Source / Network>A25A-FXS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION

·

If the auxiliary battery voltage is low, the seat heater system may not operate. When "High Power Consumption Partial Limit On AC/Heater Operation" is not displayed on the multi-information display in the combination meter assembly, check the Data List item "Battery Control Count (Body ECU)".

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST



HINT:

Inspect the fuses related to this system before inspecting the suspected areas below.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SEAT HEATER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Right Seat Heater RH side rear seat heater operation OFF/ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Right Seat Heater
50004 121 118
OK:

RH side rear seat heater operates normally.



Result:
Proceed to
OK
NG



OK

2.INSPECT SEAT HEATER (REAR) SWITCH RH

NG

7.INSPECT S/HTR R/R RELAY
2.INSPECT SEAT HEATER (REAR) SWITCH RH
a.

Remove the seat heater (rear) switch RH.

Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH (for Rear Seat)>REMOVAL


b.

Inspect the seat heater (rear) switch RH.

Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH (for Rear Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SEAT HEATER [REAR] SWITCH RH - BATTERY)

NG

REPLACE SEAT HEATER (REAR) SWITCH RH

3.CHECK HARNESS AND CONNECTOR (SEAT HEATER [REAR] SWITCH RH - BATTERY)
a.
E409348C01
1.51,0.24 1.885,0.49 0.375,0.25 2.104,1.927 1.979,1.927 1.979,1.927 1.948,1.396 true 1.615,0.281 1.865,0.448 0.25,0.167 10 false K3 0.135,0.104 0.323,0.281 0.188,0.177 10 false *a 2.156,1.854 2.375,2.031 0.219,0.177 10 false IG
*a Front view of wire harness connector
(to Seat Heater [Rear] Switch RH)


Disconnect the seat heater (rear) switch RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K3-5 (IG) - Body ground Ignition switch ON 11 to 14 V
K3-5 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SEAT HEATER [REAR] SWITCH RH - AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SEAT HEATER [REAR] SWITCH RH - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the K3 seat heater (rear) switch RH connector.


b.

Disconnect the G24 air conditioning control assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K3-4 (IND) - G24-6 (SWB) Always Below 1 Ω
K3-4 (IND) or G24-6 (SWB) - Other terminals and body ground Always 10 kΩ or higher
K3-2 (E) - G24-2 (SW2) Always Below 1 Ω
K3-2 (E) or G24-2 (SW2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE AIR CONDITIONING CONTROL ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE AIR CONDITIONING CONTROL ASSEMBLY
a.

Replace the air conditioning control assembly with a new or known good one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK REAR SEAT HEATER OPERATION
6.CHECK REAR SEAT HEATER OPERATION
a.

Check the RH side rear seat heater operation.

Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>OPERATION CHECK

OK:

RH side rear seat heater operates normally.



Result:
Proceed to
OK
NG



OK

END (AIR CONDITIONING CONTROL ASSEMBLY WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

7.INSPECT S/HTR R/R RELAY
a.
E270015N02
2.24,0.74 2.073,0.385 true 2.552,0.729 2.719,0.396 true 2.49,1.115 2.823,0.844 true 2.469,1.365 2.813,1.677 true 1.969,0.25 2.125,0.438 0.156,0.188 10 false 1 2.729,0.219 2.885,0.406 0.156,0.188 10 false 2 2.875,0.74 3.031,0.927 0.156,0.188 10 false 5 2.865,1.646 3.021,1.833 0.156,0.188 10 false 3 0.563,0.729 0.688,0.917 0.125,0.188 10 false 5 1.677,0.729 1.833,0.917 0.156,0.188 10 false 3 0.573,1.25 0.729,1.438 0.156,0.188 10 false 1 1.677,1.271 1.833,1.458 0.156,0.188 10 false 2

Remove the S/HTR R/R relay from the No. 3 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (S/HTR R/R RELAY - BATTERY)

NG

REPLACE S/HTR R/R RELAY

8.CHECK HARNESS AND CONNECTOR (S/HTR R/R RELAY - BATTERY)
E409349C01
0.229,0.188 0.438,0.385 0.208,0.198 12 false *A 0.24,2.875 0.448,3.073 0.208,0.198 12 false *B 4.719,0.573 4.948,0.75 0.229,0.177 10 false *a 0.521,4.146 0.75,4.323 0.229,0.177 10 false *a
*A for Gasoline Model *B for HV Model
*a Front view of wire harness connector
(to S/HTR R/R Relay)
- -


a.

Remove the S/HTR R/R relay from the No. 3 relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S/HTR R/R relay terminal 1 - Body ground Ignition switch ON 11 to 14 V
S/HTR R/R relay terminal 1 - Body ground Ignition switch off Below 1 V
S/HTR R/R relay terminal 5 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (S/HTR R/R RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (S/HTR R/R RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the S/HTR R/R relay from the No. 3 relay block.


b.

Disconnect the G47 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S/HTR R/R relay terminal 2 - G47-20 (SH2R) Always Below 1 Ω
S/HTR R/R relay terminal 2 or G47-20 (SH2R) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (SEAT HEATER ASSEMBLY RH [REAR SEAT CUSHION] - S/HTR R/R RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (SEAT HEATER ASSEMBLY RH [REAR SEAT CUSHION] - S/HTR R/R RELAY AND BODY GROUND)
a.

Disconnect the N43 seat heater assembly RH (rear seat cushion) connector.


b.

Remove the S/HTR R/R relay from the No. 3 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N43-1 (B) - S/HTR R/R relay terminal 3 Always Below 1 Ω
N43-1 (B) or S/HTR R/R relay terminal 3 - Other terminals and body ground Always 10 kΩ or higher
N43-3 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT SEAT HEATER ASSEMBLY RH (REAR SEAT CUSHION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT SEAT HEATER ASSEMBLY RH (REAR SEAT CUSHION)
a.

Remove the seat heater assembly RH (rear seat cushion).

Click hereVehicle Interior>SEAT>REAR SEAT CUSHION HEATER>REMOVAL


b.

Inspect the seat heater assembly RH (rear seat cushion).

Click hereVehicle Interior>SEAT>REAR SEAT CUSHION HEATER>INSPECTION


Result:
Proceed to
OK
NG



OK

12.INSPECT SEAT HEATER ASSEMBLY RH (REAR SEATBACK)

NG

REPLACE SEAT HEATER ASSEMBLY RH (REAR SEAT CUSHION)

12.INSPECT SEAT HEATER ASSEMBLY RH (REAR SEATBACK)
a.

Remove the seat heater assembly RH (rear seatback).

Click hereVehicle Interior>SEAT>REAR SEATBACK HEATER>REMOVAL


b.

Inspect the seat heater assembly RH (rear seatback).

Click hereVehicle Interior>SEAT>REAR SEATBACK HEATER>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE SEAT HEATER ASSEMBLY RH (REAR SEATBACK)