Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)
RM3620E _58 Vehicle Interior _076405 SEAT _0375764 FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory)  One or more Power Seat Motors do not Operate  


DESCRIPTION

Signals are input into the position control ECU assembly driver seat. The built-in ECU manages the signals received from the position control ECU assembly (driver seat) and operates each motor. If the position control ECU assembly (driver seat) receives 2 or more operation signals for the same motor, the motor will be stopped. Manual operation resumes when the position control ECU assembly (driver seat) receives only 1 signal.

WIRING DIAGRAM

B531525E02
4.969,2.604 5.427,2.802 0.458,0.198 10 false S7 4.958,0.875 5.417,1.073 0.458,0.198 10 false S7 4.958,4.896 5.417,5.094 0.458,0.198 10 false S7 4.969,5.417 5.427,5.615 0.458,0.198 10 false S7 4.958,6.75 5.417,6.948 0.458,0.198 10 false S7 4.969,8.177 5.427,8.375 0.458,0.198 10 false S7 4.969,8.698 5.427,8.896 0.458,0.198 10 false S6 4.958,1.396 5.417,1.594 0.458,0.198 10 false S6 4.969,3.135 5.427,3.333 0.458,0.198 10 false S6 4.969,7.271 5.427,7.469 0.458,0.198 10 false S6 4.49,0.875 4.948,1.073 0.458,0.198 10 false T7 4.479,2.604 4.938,2.802 0.458,0.198 10 false T7 4.49,4.896 4.948,5.094 0.458,0.198 10 false T7 4.49,5.417 4.948,5.615 0.458,0.198 10 false T7 4.49,6.75 4.948,6.948 0.458,0.198 10 false T7 4.49,8.177 4.948,8.375 0.458,0.198 10 false T7 4.479,8.688 4.938,8.885 0.458,0.198 10 false T6 4.479,1.396 4.938,1.594 0.458,0.198 10 false T6 4.49,3.125 4.948,3.323 0.458,0.198 10 false T6 4.49,7.271 4.948,7.469 0.458,0.198 10 false T6 2.708,2.49 2.865,2.688 0.156,0.198 10 false 1 2.719,0.75 2.875,0.948 0.156,0.198 10 false 1 2.698,5.292 2.854,5.49 0.156,0.198 10 false 1 2.729,1.271 2.885,1.469 0.156,0.198 10 false 2 2.698,3 2.854,3.198 0.156,0.198 10 false 4 5.354,0.844 5.667,1.042 0.313,0.198 10 false L+ 5.365,1.365 5.677,1.563 0.313,0.198 10 false L- 4.948,0.635 5.406,0.833 0.458,0.198 10 false 9*2 4.448,0.635 4.906,0.833 0.458,0.198 10 false 9*1 4.917,1.146 5.375,1.344 0.458,0.198 10 false 3*2 4.438,1.146 4.896,1.344 0.458,0.198 10 false 3*1 0.813,1.604 1.667,1.875 0.854,0.271 10 false T24*1, S24*2 0.823,1.76 4.427,2.375 3.604,0.615 10 false Lumbar Support Adjuster Assembly (Driver Seat) 5.344,2.583 5.958,2.781 0.615,0.198 10 false RCL+ 5.354,3.094 5.969,3.292 0.615,0.198 10 false RCL- 4.396,2.354 5.01,2.552 0.615,0.198 10 false 10*1 4.885,2.354 5.5,2.552 0.615,0.198 10 false 10*2 4.438,2.875 4.896,3.073 0.458,0.198 10 false 6*1 4.927,2.875 5.385,3.073 0.458,0.198 10 false 6*2 1.875,3.375 2.979,3.615 1.104,0.24 10 false T23*1, S23*2 1.865,3.51 4.156,3.708 2.292,0.198 10 false Reclining Motor 0.75,3.885 5.833,4.25 5.083,0.365 10 false Front Seatback Frame Sub-assembly (Driver Seat) 2.708,4.771 2.865,4.969 0.156,0.198 10 false 4 2.708,6.656 2.865,6.854 0.156,0.198 10 false 1 2.708,7.146 2.865,7.344 0.156,0.198 10 false 4 2.719,8.615 2.875,8.813 0.156,0.198 10 false 4 2.698,8.083 2.854,8.281 0.156,0.198 10 false 1 1.938,5.667 2.927,6.01 0.99,0.344 10 false T1*1, S1*2 1.938,5.813 3.625,6.01 1.688,0.198 10 false Slide Motor 0.875,7.635 5.5,8.052 4.625,0.417 10 false Power Seat Tilt Motor Assembly (Driver Seat) 0.875,7.458 1.802,7.781 0.927,0.323 10 false T9*1, S9*2 0.854,8.875 2.052,9.302 1.198,0.427 10 false T12*1, S12*2 0.854,9.052 4.031,9.594 3.177,0.542 10 false Power Seat Lifter Motor Assembly (Driver Seat) 0.979,6.219 5.823,6.573 4.844,0.354 10 false Front Seat Adjuster Assembly (Driver Seat) 4.938,9.146 6.906,9.698 1.969,0.552 10 false Position Control ECU Assembly (Driver Seat) 5.344,4.875 5.958,5.073 0.615,0.198 10 false SLD+ 5.344,5.385 5.958,5.583 0.615,0.198 10 false SLD- 5.354,7.271 5.969,7.469 0.615,0.198 10 false FRV- 5.354,6.75 5.969,6.948 0.615,0.198 10 false FRV+ 5.344,8.708 5.958,8.906 0.615,0.198 10 false LFT- 5.344,8.198 5.958,8.396 0.615,0.198 10 false LFT+ 4.438,4.646 4.896,4.844 0.458,0.198 10 false 1*1 4.927,4.646 5.385,4.844 0.458,0.198 10 false 1*2 4.448,5.156 4.906,5.354 0.458,0.198 10 false 5*1 4.927,5.156 5.385,5.354 0.458,0.198 10 false 5*2 4.458,6.51 4.917,6.708 0.458,0.198 10 false 7*1 4.938,6.51 5.396,6.708 0.458,0.198 10 false 7*2 4.448,7.042 4.906,7.24 0.458,0.198 10 false 4*1 4.958,7.042 5.417,7.24 0.458,0.198 10 false 4*2 4.438,7.938 4.896,8.135 0.458,0.198 10 false 6*1 4.938,7.938 5.396,8.135 0.458,0.198 10 false 6*2 4.448,8.458 4.906,8.656 0.458,0.198 10 false 5*1 4.938,8.469 5.396,8.667 0.458,0.198 10 false 5*2 0.281,9.531 1.969,9.729 1.688,0.198 10 false *1: for LHD 1.521,9.531 3.208,9.729 1.688,0.198 10 false *2: for RHD

B532101E01
0.708,1.365 0.865,1.563 0.156,0.198 10 false E 0.26,1.198 0.604,1.552 0.344,0.354 10 false 20*1, 11*2 2.344,1.083 2.906,1.271 0.563,0.188 10 false 6*1, 5*2 1.844,1.083 2.281,1.271 0.438,0.188 10 false SLDR 1.854,1.656 2.292,1.844 0.438,0.188 10 false SLDF 1.844,2.208 2.281,2.396 0.438,0.188 10 false RCLR 1.844,2.802 2.281,2.99 0.438,0.188 10 false RCLF 1.906,3.365 2.344,3.552 0.438,0.188 10 false FUP 1.781,3.927 2.219,4.115 0.438,0.188 10 false FDWN 1.917,4.5 2.354,4.688 0.438,0.188 10 false LUP 1.781,5.042 2.292,5.24 0.51,0.198 10 false LDWN 2.073,5.625 2.51,5.813 0.438,0.188 10 false H 2.073,6.188 2.51,6.375 0.438,0.188 10 false R 5.344,0.656 5.781,0.844 0.438,0.188 10 false SGND 5.354,1.792 5.792,1.979 0.438,0.188 10 false SLDF 5.344,2.344 5.781,2.531 0.438,0.188 10 false RCLR 5.344,2.917 5.781,3.104 0.438,0.188 10 false RCLF 5.344,3.469 5.781,3.656 0.438,0.188 10 false FRVU 5.354,4.042 5.792,4.229 0.438,0.188 10 false FRVD 5.354,4.604 5.792,4.792 0.438,0.188 10 false LFTU 5.354,5.167 5.792,5.354 0.438,0.188 10 false LFTD 5.365,5.74 5.802,5.927 0.438,0.188 10 false LFLF 5.354,6.313 5.792,6.5 0.438,0.188 10 false LFLR 2.354,1.656 2.917,1.844 0.563,0.188 10 false 7*1, 4*2 2.354,2.219 3.042,2.375 0.688,0.156 10 false 1*1, 10*2 2.354,2.781 2.917,2.969 0.563,0.188 10 false 2*1, 9*2 2.354,3.354 2.917,3.542 0.563,0.188 10 false 4*1, 7*2 2.354,3.906 2.917,4.094 0.563,0.188 10 false 5*1, 6*2 2.354,4.49 2.917,4.677 0.563,0.188 10 false 3*1, 8*2 2.365,5.052 3.167,5.24 0.802,0.188 10 false 8*1, 3*2 2.344,5.625 3.104,5.802 0.76,0.177 10 false 14*1, 17*2 2.344,6.188 3.146,6.438 0.802,0.25 10 false 17*1, 14*2 4.406,0.958 4.771,1.167 0.365,0.208 10 false 23*1 4.906,0.958 5.333,1.177 0.427,0.219 10 false 23*2 4.927,1.531 5.229,1.74 0.302,0.208 10 false 9*2 4.448,1.531 4.75,1.74 0.302,0.208 10 false 9*1 4.406,2.094 4.781,2.313 0.375,0.219 10 false 22*1 4.906,2.094 5.333,2.323 0.427,0.229 10 false 22*2 4.927,2.667 5.229,2.875 0.302,0.208 10 false 8*2 4.427,2.667 4.729,2.875 0.302,0.208 10 false 8*1 4.438,3.219 4.74,3.427 0.302,0.208 10 false 6*1 4.906,3.219 5.208,3.427 0.302,0.208 10 false 6*2 4.885,3.792 5.302,4.031 0.417,0.24 10 false 20*2 4.406,3.792 4.813,4.021 0.406,0.229 10 false 20*1 4.417,4.354 4.719,4.563 0.302,0.208 10 false 7*1 4.917,4.354 5.219,4.563 0.302,0.208 10 false 7*2 4.896,4.927 5.375,5.188 0.479,0.26 10 false 21*2 4.396,4.927 4.802,5.167 0.406,0.24 10 false 21*1 4.448,5.479 4.75,5.688 0.302,0.208 10 false 4*1 4.927,5.49 5.229,5.698 0.302,0.208 10 false 4*2 4.885,6.052 5.292,6.26 0.406,0.208 10 false 18*2 4.396,6.052 4.813,6.302 0.417,0.25 10 false 18*1 4.469,6.292 4.771,6.5 0.302,0.208 10 false T8 4.469,5.729 4.771,5.938 0.302,0.208 10 false T8 4.469,5.167 4.771,5.375 0.302,0.208 10 false T8 4.469,4.583 4.771,4.792 0.302,0.208 10 false T8 4.469,4.031 4.771,4.24 0.302,0.208 10 false T8 4.469,3.458 4.771,3.667 0.302,0.208 10 false T8 4.469,2.906 4.771,3.115 0.302,0.208 10 false T8 4.469,2.333 4.771,2.542 0.302,0.208 10 false T8 4.469,1.771 4.771,1.979 0.302,0.208 10 false T8 4.469,1.198 4.771,1.406 0.302,0.208 10 false T8 4.938,1.198 5.24,1.406 0.302,0.208 10 false S8 4.938,1.771 5.24,1.979 0.302,0.208 10 false S8 4.938,2.333 5.24,2.542 0.302,0.208 10 false S8 4.938,2.896 5.24,3.104 0.302,0.208 10 false S8 4.938,3.469 5.24,3.677 0.302,0.208 10 false S8 4.948,4.031 5.25,4.24 0.302,0.208 10 false S8 4.938,4.583 5.24,4.792 0.302,0.208 10 false S8 4.938,5.167 5.24,5.375 0.302,0.208 10 false S8 4.938,5.729 5.24,5.938 0.302,0.208 10 false S8 4.938,6.292 5.24,6.5 0.302,0.208 10 false S8 0.323,6.854 2.01,7.052 1.688,0.198 10 false T14*1, S14*2 0.302,7.042 2.646,7.281 2.344,0.24 10 false Front Power Seat Switch (Driver Seat) 4.969,6.854 6.979,7.229 2.01,0.375 10 false Position Control ECU Assembly (Driver Seat) 5.365,1.219 5.802,1.406 0.438,0.188 10 false SLDR 4.469,0.635 4.771,0.844 0.302,0.208 10 false T8 4.948,0.635 5.25,0.844 0.302,0.208 10 false S8 4.396,0.385 4.76,0.594 0.365,0.208 10 false 12*1 4.875,0.385 5.24,0.594 0.365,0.208 10 false 12*2 0.25,7.479 1.073,7.656 0.823,0.177 10 false *1: for LHD 1.292,7.479 2.115,7.656 0.823,0.177 10 false *2: for RHD


CAUTION / NOTICE / HINT

NOTICE:

Initializing the position control ECU assembly (driver seat) will clear the seat position memory.


HINT:

Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>REGISTRATION


PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK


Result:
Result Proceed to
One or more power seat functions do not operate A
All power seat functions do not operate B



A

2.READ VALUE USING GTS (POWER SEAT SWITCH)

B

GO TO OTHER DIAGNOSIS PROCEDURE (Front Power Seat does not Operate with Front Power Seat Switch)

2.READ VALUE USING GTS (POWER SEAT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reclining Rear Reclining switch signal (Rearward) ON or OFF ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
-
Reclining Front Reclining switch signal (Forward) ON or OFF ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
-
Front Vertical Down Front vertical switch signal (Downward) ON or OFF ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
-
Front Vertical Up Front vertical switch signal (Upward) ON or OFF ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
-
Lifter Switch Down Rear lifter switch signal (Downward) ON or OFF ON: Rear lifter switch (Downward) on
OFF: Rear lifter switch (Downward) off
-
Lifter Switch Up Rear lifter switch signal (Upward) ON or OFF ON: Rear lifter switch (Upward) on
OFF: Rear lifter switch (Upward) off
-
Slide Rear Slide switch signal (Rearward) ON or OFF ON: Slide switch (Rearward) on
OFF: Slide switch (Rearward) off
-
Slide Front Slide switch signal (Forward) ON or OFF ON: Slide switch (Forward) on
OFF: Slide switch (Forward) off
-
Lumbar Switch Front Lumbar support adjuster switch signal (Forward) ON or OFF ON: Lumbar support adjuster switch (Forward) on
OFF: Lumbar support adjuster switch (Forward) off
-
Lumbar Switch Rear Lumbar support adjuster switch signal (Rearward) ON or OFF ON: Lumbar support adjuster switch (Rearward) on
OFF: Lumbar support adjuster switch (Rearward) off
-
Body Electrical > Driver Seat > Data List
Tester Display
Reclining Rear
Reclining Front
Front Vertical Down
Front Vertical Up
Lifter Switch Down
Lifter Switch Up
Slide Rear
Slide Front
Lumbar Switch Front
Lumbar Switch Rear
50003 162 17,18,19,20,21,22,23,24,157,158
OK:

On the GTS screen, ON or OFF is displayed accordingly



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR)

NG

14.INSPECT FRONT POWER SEAT SWITCH (DRIVER SEAT)
3.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR)
a.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Lifter Operation Seat lifter operation OFF/Down/Up -
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Lumbar Slide Lumbar support operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
Body Electrical > Driver Seat > Active Test
Tester Display
Front Vertical Operation
50004 162 3
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
Body Electrical > Driver Seat > Active Test
Tester Display
Lumbar Slide
50004 162 8

Result:
Result Proceed to
Slide function does not operate normally A
Front vertical function does not operate normally B
Lifter function does not operate normally C
Reclining function does not operate normally D
Lumbar support adjustment function does not operate normally E



A

4.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY [DRIVER SEAT])

B

6.INSPECT POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)

C

8.INSPECT POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

D

10.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY [DRIVER SEAT])

E

12.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY (DRIVER SEAT)
4.INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY [DRIVER SEAT])
a.

Remove the slide motor (front seat adjuster assembly [driver seat]).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


b.

Inspect the slide motor (front seat adjuster assembly [driver seat]).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)])

NG

REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY [DRIVER SEAT])

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - SLIDE MOTOR [FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)])
a.

Disconnect the T7*1 or S7*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T1*1 or S1*2 slide motor (front seat adjuster assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T7-1 (SLD+) - T1-4 Always Below 1 Ω
T7-1 (SLD+) or T1-4 - Other terminals and body ground Always 10 kΩ or higher
T7-5 (SLD-) - T1-1 Always Below 1 Ω
T7-5 (SLD-) or T1-1 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S7-1 (SLD+) - S1-4 Always Below 1 Ω
S7-1 (SLD+) or S1-4 - Other terminals and body ground Always 10 kΩ or higher
S7-5 (SLD-) - S1-1 Always Below 1 Ω
S7-5 (SLD-) or S1-1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)
a.

Remove the power seat tilt motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL


b.

Inspect the power seat tilt motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT TILT MOTOR ASSEMBLY [DRIVER SEAT])

NG

REPLACE POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT TILT MOTOR ASSEMBLY [DRIVER SEAT])
a.

Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.


b.

Disconnect the T9*1 or S9*2 power seat tilt motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T7-7 (FRV+) - T9-1 Always Below 1 Ω
T7-7 (FRV+) or T9-1 - Other terminals and body ground Always 10 kΩ or higher
T6-4 (FRV-) - T9-4 Always Below 1 Ω
T6-4 (FRV-) or T9-4 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S7-7 (FRV+) - S9-1 Always Below 1 Ω
S7-7 (FRV+) or S9-1 - Other terminals and body ground Always 10 kΩ or higher
S6-4 (FRV-) - S9-4 Always Below 1 Ω
S6-4 (FRV-) or S9-4 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
a.

Remove the power seat lifter motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL


b.

Inspect the power seat lifter motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT LIFTER MOTOR ASSEMBLY [DRIVER SEAT])

NG

REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - POWER SEAT LIFTER MOTOR ASSEMBLY [DRIVER SEAT])
a.

Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.


b.

Disconnect the T12*1 or S12*2 power seat lifter motor assembly (driver seat) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T7-6 (LFT+) - T12-1 Always Below 1 Ω
T7-6 (LFT+) or T12-1 - Other terminals and body ground Always 10 kΩ or higher
T6-5 (LFT-) - T12-4 Always Below 1 Ω
T6-5 (LFT-) or T12-4 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S7-6 (LFT+) - S12-1 Always Below 1 Ω
S7-6 (LFT+) or S12-1 - Other terminals and body ground Always 10 kΩ or higher
S6-5 (LFT-) - S12-4 Always Below 1 Ω
S6-5 (LFT-) or S12-4 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY [DRIVER SEAT])
a.

Remove the reclining motor (front seatback frame sub-assembly [driver seat]).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


b.

Inspect the reclining motor (front seatback frame sub-assembly [driver seat]).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)])

NG

REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY [DRIVER SEAT])

11.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - RECLINING MOTOR [FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)])
a.

Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.


b.

Disconnect the T23*1 or S23*2 reclining motor (front seatback frame sub-assembly [driver seat]) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T7-10 (RCL+) - T23-1 Always Below 1 Ω
T7-10 (RCL+) or T23-1 - Other terminals and body ground Always 10 kΩ or higher
T6-6 (RCL-) - T23-4 Always Below 1 Ω
T6-6 (RCL-) or T23-4 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S7-10 (RCL+) - S23-1 Always Below 1 Ω
S7-10 (RCL+) or S23-1 - Other terminals and body ground Always 10 kΩ or higher
S6-6 (RCL-) - S23-4 Always Below 1 Ω
S6-6 (RCL-) or S23-4 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY (DRIVER SEAT)
a.

Remove the lumbar support adjuster assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>REMOVAL


b.

Inspect the lumbar support adjuster assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - LUMBAR SUPPORT ADJUSTER ASSEMBLY [DRIVER SEAT])

NG

REPLACE LUMBAR SUPPORT ADJUSTER ASSEMBLY (DRIVER SEAT)

13.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - LUMBAR SUPPORT ADJUSTER ASSEMBLY [DRIVER SEAT])
a.

Disconnect the T7*1 and T6*1 or S7*2 and S6*2 position control ECU assembly (driver seat) connectors.


b.

Disconnect the T24*1 or S24*2 lumbar support adjuster assembly (driver seat) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the wire harness and connector between the position control ECU assembly (driver seat) and applicable motor.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T7-9 (L+) - T24-1 Always Below 1 Ω
T7-9 (L+) or T24-1 - Other terminals and body ground Always 10 kΩ or higher
T6-3 (L-) - T24-2 Always Below 1 Ω
T6-3 (L-) or T24-2 - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
S7-9 (L+) - S24-1 Always Below 1 Ω
S7-9 (L+) or S24-1 - Other terminals and body ground Always 10 kΩ or higher
S6-3 (L-) - S24-2 Always Below 1 Ω
S6-3 (L-) or S24-2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT FRONT POWER SEAT SWITCH (DRIVER SEAT)
a.

Remove the front power seat switch (driver seat).

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH>REMOVAL


b.

Inspect the front power seat switch (driver seat).

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - FRONT POWER SEAT SWITCH [DRIVER SEAT])

NG

REPLACE FRONT POWER SEAT SWITCH (DRIVER SEAT)

15.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] - FRONT POWER SEAT SWITCH [DRIVER SEAT])
a.

Disconnect the T8*1 or S8*2 position control ECU assembly (driver seat) connector.


b.

Disconnect the T14*1 or S14*2 front power seat switch (driver seat) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
T14-6 (SLDR) - T8-23 (SLDR) Always Below 1 Ω
T14-6 (SLDR) or T8-23 (SLDR) - Other terminals and body ground Always 10 kΩ or higher
T14-7 (SLDF) - T8-9 (SLDF) Always Below 1 Ω
T14-7 (SLDF) or T8-9 (SLDF) - Other terminals and body ground Always 10 kΩ or higher
T14-1 (RCLR) - T8-22 (RCLR) Always Below 1 Ω
T14-1 (RCLR) or T8-22 (RCLR) - Other terminals and body ground Always 10 kΩ or higher
T14-2 (RCLF) - T8-8 (RCLF) Always Below 1 Ω
T14-2 (RCLF) or T8-8 (RCLF) - Other terminals and body ground Always 10 kΩ or higher
T14-4 (FUP) - T8-6 (FRVU) Always Below 1 Ω
T14-4 (FUP) or T8-6 (FRVU) - Other terminals and body ground Always 10 kΩ or higher
T14-5 (FDWN) - T8-20 (FRVD) Always Below 1 Ω
T14-5 (FDWN) or T8-20 (FRVD) - Other terminals and body ground Always 10 kΩ or higher
T14-3 (LUP) - T8-7 (LFTU) Always Below 1 Ω
T14-3 (LUP) or T8-7 (LFTU) - Other terminals and body ground Always 10 kΩ or higher
T14-8 (LDWN) - T8-21 (LFTD) Always Below 1 Ω
T14-8 (LDWN) or T8-21 (LFTD) - Other terminals and body ground Always 10 kΩ or higher
T14-14 (H) - T8-4 (LFLF) Always Below 1 Ω
T14-14 (H) or T8-4 (LFLF) - Other terminals and body ground Always 10 kΩ or higher
T14-17 (R) - T8-18 (LFLR) Always Below 1 Ω
T14-17 (R) or T8-18 (LFLR) - Other terminals and body ground Always 10 kΩ or higher
T14-20 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
S14-5 (SLDR) - S8-23 (SLDR) Always Below 1 Ω
S14-5 (SLDR) or S8-23 (SLDR) - Other terminals and body ground Always 10 kΩ or higher
S14-4 (SLDF) - S8-9 (SLDF) Always Below 1 Ω
S14-4 (SLDF) or S8-9 (SLDF) - Other terminals and body ground Always 10 kΩ or higher
S14-10 (RCLR) - S8-22 (RCLR) Always Below 1 Ω
S14-10 (RCLR) or S8-22 (RCLR) - Other terminals and body ground Always 10 kΩ or higher
S14-9 (RCLF) - S8-8 (RCLF) Always Below 1 Ω
S14-9 (RCLF) or S8-8 (RCLF) - Other terminals and body ground Always 10 kΩ or higher
S14-7 (FUP) - S8-6 (FRVU) Always Below 1 Ω
S14-7 (FUP) or S8-6 (FRVU) - Other terminals and body ground Always 10 kΩ or higher
S14-6 (FDWN) - S8-20 (FRVD) Always Below 1 Ω
S14-6 (FDWN) or S8-20 (FRVD) - Other terminals and body ground Always 10 kΩ or higher
S14-8 (LUP) - S8-7 (LFTU) Always Below 1 Ω
S14-8 (LUP) or S8-7 (LFTU) - Other terminals and body ground Always 10 kΩ or higher
S14-3 (LDWN) - S8-21 (LFTD) Always Below 1 Ω
S14-3 (LDWN) or S8-21 (LFTD) - Other terminals and body ground Always 10 kΩ or higher
S14-17 (H) - S8-4 (LFLF) Always Below 1 Ω
S14-17 (H) or S8-4 (LFLF) - Other terminals and body ground Always 10 kΩ or higher
S14-14 (R) - S8-18 (LFLR) Always Below 1 Ω
S14-14 (R) or S8-18 (LFLR) - Other terminals and body ground Always 10 kΩ or higher
S14-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR