Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)
RM3620E _58 Vehicle Interior _076405 SEAT _0375764 FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for Gasoline Model with Memory)  Power Seat Position is not Memorized  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives seat memory switch signals. If the SET switch is being pressed when one of the M1 or M2 switches is pressed, or if one of the M1 or M2 switches is pressed within 3 seconds of pressing the SET switch, the main body ECU (multiplex network body ECU) sends a memory request signal to the position control ECU assembly (driver seat). After receiving the request signal, the position control ECU assembly (driver seat) memorizes the location data of each motor.

WIRING DIAGRAM

B531534E03
0.104,1.198 2.052,1.615 1.948,0.417 10 false Position Control ECU Assembly (Driver Seat) 3.104,2.844 4.74,3.229 1.635,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 0.688,3.458 2.458,3.677 1.771,0.219 10 false : CAN Communication Line 4.396,0.458 4.875,0.729 0.479,0.271 10 false M1 4.719,1.667 5.198,1.938 0.479,0.271 10 false 7 4.719,1.01 5.198,1.281 0.479,0.271 10 false 9 4.698,0.344 5.177,0.615 0.479,0.271 10 false 10 5.354,2.26 5.833,2.531 0.479,0.271 10 false 1 5.552,2.26 6.031,2.531 0.479,0.271 10 false E 5.521,2.969 6.833,3.385 1.313,0.417 10 false Seat Memory Switch (Driver Door) 4.375,1.115 4.854,1.385 0.479,0.271 10 false M2 4.344,1.771 4.823,2.042 0.479,0.271 10 false MM 5.344,0.344 5.823,0.615 0.479,0.271 10 false 3 5.354,1 5.833,1.271 0.479,0.271 10 false 4 5.344,1.667 5.823,1.938 0.479,0.271 10 false 2 5.542,0.865 5.792,1.042 0.25,0.177 10 false 2*1 5.542,1.49 6.146,1.667 0.604,0.177 10 false MMRY*1 3.115,2.646 3.458,2.854 0.344,0.208 10 false G43 5.521,2.813 6.5,3.083 0.979,0.271 10 false J4*1, I5*2 3.792,3.5 5.479,3.698 1.688,0.198 10 false *1: for LHD 4.75,3.479 6.438,3.677 1.688,0.198 10 false *2: for RHD 5.521,0.25 5.76,0.417 0.24,0.167 10 false 1*1 5.542,1.656 6.083,1.813 0.542,0.156 10 false MRY*2 5.531,0.385 5.927,0.542 0.396,0.156 10 false M1*2 5.531,1.021 5.927,1.198 0.396,0.177 10 false M2*2


CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a restoring operation has failed, release all of the switches. The seat memory restoring function will not operate unless the switches are released.

·

The front power seat control system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to the Service Bulletin.

·

Initializing the position control ECU assembly (driver seat) will clear the seat position memory.



HINT:

Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>REGISTRATION


PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for Gasoline Model with Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the front power seat switch (driver seat).



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (M1, M2, SET SWITCH)

NG

2.READ VALUE USING GTS (M1, M2, SET SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
M1 Switch M1 switch signal ON or OFF ON: M1 switch on
OFF: M1 switch off
-
M2 Switch M2 switch signal ON or OFF ON: M2 switch on
OFF: M2 switch off
-
SET Switch SET switch signal ON or OFF ON: SET switch on
OFF: SET switch off
-
Body Electrical > Main Body > Data List
Tester Display
M1 Switch
M2 Switch
SET Switch
50003 123 213,214,216
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (BUZZER)

NG

4.INSPECT SEAT MEMORY SWITCH (DRIVER DOOR)
3.PERFORM ACTIVE TEST USING GTS (BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer operation OFF/ON -
Body Electrical > Driver Seat > Active Test
Tester Display
Buzzer
50004 162 5
OK:

Buzzer sounds normally.



Result:
Proceed to
OK
NG



OK

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

4.INSPECT SEAT MEMORY SWITCH (DRIVER DOOR)
a.

Remove the seat memory switch (driver door).

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL


b.

Inspect the seat memory switch (driver door).

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH [DRIVER DOOR] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE SEAT MEMORY SWITCH (DRIVER DOOR)

5.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH [DRIVER DOOR] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the G43 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the J4*1 or I5*2 seat memory switch (driver door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G43-7 (MM) - J4-2 (MMRY) Always Below 1 Ω
G43-7 (MM) or J4-2 (MMRY) - Other terminals and body ground Always 10 kΩ or higher
G43-10 (M1) - J4-3 (1) Always Below 1 Ω
G43-10 (M1) or J4-3 (1) - Other terminals and body ground Always 10 kΩ or higher
G43-9 (M2) - J4-4 (2) Always Below 1 Ω
G43-9 (M2) or J4-4 (2) - Other terminals and body ground Always 10 kΩ or higher
J4-1 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
G43-7 (MM) - I5-2 (MRY) Always Below 1 Ω
G43-7 (MM) or I5-2 (MRY) - Other terminals and body ground Always 10 kΩ or higher
G43-10 (M1) - I5-3 (M1) Always Below 1 Ω
G43-10 (M1) or I5-3 (M1) - Other terminals and body ground Always 10 kΩ or higher
G43-9 (M2) - I5-4 (M2) Always Below 1 Ω
G43-9 (M2) or I5-4 (M2) - Other terminals and body ground Always 10 kΩ or higher
I5-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR