Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for LHD)
RM3620E _52 Drivetrain _076045 CLUTCH _0370081 CLUTCH PEDAL(for LHD) G

CLUTCH  CLUTCH PEDAL(for LHD)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 67914B 1.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 2.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 4.INSPECT CLUTCH PEDAL HEIGHT

a.

Fold back the floor carpet.


b.

Check that the clutch pedal height is correct.

C403485C01
5.646,1.021 6,0.583 6,0.583 6.333,0.583 true 2.5,2.333 3,2.333 true 6.417,0.5 6.729,0.698 0.313,0.198 10 false *1 6.188,1.75 6.5,1.948 0.313,0.198 10 false *a 2.406,1.802 2.635,2 0.229,0.198 10 true *a 3.083,2.25 3.313,2.479 0.229,0.229 10 true *b 0.948,0.875 1.198,1.125 0.25,0.25 10 true *c
*1 Clutch Pedal Pad - -
*a Clutch Pedal Height *b Measuring Plane of Floor Panel
*c 30 mm (1.18 in.) - -


Clutch pedal height from floor panel:

170.1 to 188.1 mm (6.70 to 7.40 in.)


·

If the result is not as specified, bleed the clutch line and perform the inspection again.

·

If the result is not as specified after bleeding the clutch line, replace the clutch master cylinder assembly.



c.

Install the floor carpet.


Hide 5.INSPECT CLUTCH PEDAL FREE PLAY

a.
C408781C01
2.104,1.823 2.417,2.021 0.313,0.198 10 false *a
*a Pedal Free Play


Check that the clutch pedal free play is correct.

HINT:

Pay close attention to the change in resistance to distinguish clutch pedal free play while performing the inspection.


i.

Depress the clutch pedal until clutch resistance begins to be felt.

Clutch pedal free play (Reference):

3 to 15 mm (0.118 to 0.591 in.)


·

If the result is not as specified, bleed the clutch line and perform the inspection again.

·

If the result is not as specified after bleeding the clutch line, replace the clutch master cylinder assembly.




Hide 6.INSPECT CLUTCH RELEASE POINT

CAUTION:

When checking the clutch release point, ensure that the vehicle is secure.


a.
C227877C10
1.365,1.177 1.615,1.177 false 1.615,1.583 2.281,1.042 2.281,1.042 2.396,1.042 true 1.354,1.521 0.906,1.885 0.906,1.885 0.802,1.885 true 1.396,0.99 1.635,1.198 0.24,0.208 10 false *c 1.802,1.917 2.063,2.125 0.26,0.208 10 false *d 0.646,1.802 0.948,2.052 0.302,0.25 10 false *b 2.458,0.969 2.719,1.198 0.26,0.229 10 false *a
*a Release Point
*b Full Stroke End Position
*c Distance from Clutch Pedal Stroke End Position to Release Point
*d Clutch Pedal Stroke


Check the clutch release point.

i.

Be sure to apply the parking brake and secure the wheels using wheel chocks.


ii.

Start the engine and run it at idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever to reverse until the gears contact.


iv.

Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard distance:

25 mm (0.984 in.) or more (from clutch pedal stroke end position to release point)


Clutch pedal stroke at 200 N (20 kgf, 45.0 lbf):
Reference value:

146 to 156 mm (5.75 to 6.14 in.)


If the distance is not as specified, perform the following procedure:

·

Check the clutch pedal height.

·

Check the clutch pedal free play.

·

Bleed the clutch line.

·

Check the clutch cover and the clutch disc.




Hide 89280 7.ADJUST CLUTCH PEDAL STROKE SENSOR ASSEMBLY

Hide 55606 8.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 67914B 10.INSTALL FRONT DOOR SCUFF PLATE LH