Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for M20A-FKS)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374931 AIR CONDITIONING UNIT(for M20A-FKS) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for M20A-FKS)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure as for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 88501 3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

Hide 88515 4.INSTALL COOLER EXPANSION VALVE

a.

Remove the vinyl tape from the No. 1 cooler evaporator sub-assembly and cooler expansion valve.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.

Compressor Oil:
Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent



c.

Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.
E407620C01
0.135,0.115 0.51,0.354 0.375,0.24 12 false *A 0.135,2.448 0.51,2.688 0.375,0.24 12 false *B
*A for Type A
*B for Type B


Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)

NOTICE:

Make sure not to cut the O-ring while installing it. (Cut O-rings cannot be installed)



Hide 87107A 6.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

Hide 87050D 9.INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

Hide 87050C 10.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

Hide 82210K 11.INSTALL AIR CONDITIONING HARNESS ASSEMBLY

a.

Attach the clamp and guide.

E408888C01
0.292,0.375 0.667,0.615 0.375,0.24 12 false *A 0.292,2.844 0.854,3.115 0.563,0.271 12 false *B, *C 0.292,5.323 0.854,5.594 0.563,0.271 12 false *B, *D 4.438,1.229 4.604,1.406 0.167,0.177 10 true *a 4.99,0.833 5.156,1.01 0.167,0.177 10 true *a 5.427,0.802 5.594,0.979 0.167,0.177 10 true *a 5.135,1.406 5.302,1.583 0.167,0.177 10 true *a 4.448,1.719 4.615,1.896 0.167,0.177 10 true *a 4.219,2.302 4.802,2.771 0.583,0.469 10 false *a 1.438,1.167 1.604,1.344 0.167,0.177 10 true *b 1.656,3.052 1.823,3.229 0.167,0.177 10 true *b 2.719,4.24 2.885,4.417 0.167,0.177 10 true *b 2.688,4.667 2.854,4.844 0.167,0.177 10 true *b 2.833,3.625 3,3.802 0.167,0.177 10 true *a 4.167,4.073 4.333,4.25 0.167,0.177 10 true *a 4.333,4.75 4.5,4.927 0.167,0.177 10 true *a 4.615,4.438 4.781,4.615 0.167,0.177 10 true *a 5.333,4.813 5.5,4.99 0.167,0.177 10 true *a 5.354,3.865 5.521,4.042 0.167,0.177 10 true *a 4.688,4.052 4.854,4.229 0.167,0.177 10 true *a 5.135,3.646 5.302,3.823 0.167,0.177 10 true *b 4.615,3.521 4.781,3.698 0.167,0.177 10 true *b 1.594,5.438 1.76,5.615 0.167,0.177 10 true *b 2.688,6.615 2.854,6.792 0.167,0.177 10 true *b 2.677,7.115 2.844,7.292 0.167,0.177 10 true *b 2.833,6.042 3,6.219 0.167,0.177 10 true *a 4.188,6.552 4.354,6.729 0.167,0.177 10 true *a 4.344,7.25 4.51,7.427 0.167,0.177 10 true *a 4.823,7.146 4.99,7.323 0.167,0.177 10 true *a 4.708,6.531 4.875,6.708 0.167,0.177 10 true *a 5.333,7.313 5.5,7.49 0.167,0.177 10 true *a 5.365,6.344 5.531,6.521 0.167,0.177 10 true *a 4.646,6 4.813,6.177 0.167,0.177 10 true *b 5.125,6.115 5.292,6.292 0.167,0.177 10 true *b
*A for LHD *B for RHD
*C for Two Layer Blower Type *D for Single Layer Blower Type
*a Clamp *b Guide



b.

Connect each connector to install the air conditioning harness assembly.


Hide 88539C 12.INSTALL NO. 2 COOLER UNIT DRAIN HOSE (Available as Supply Part)

Hide 88625Q 14.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR) (for Automatic Air Conditioning System)

Hide 88897P 15.INSTALL ASPIRATOR (for Automatic Air Conditioning System)

Hide 88898D 16.INSTALL GROMMET (for Manual Air Conditioning System)

Hide 87130D 18.INSTALL BLOWER ASSEMBLY