Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD with Vacuum Brake Booster)
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377037 BRAKE BOOSTER(for LHD with Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD with Vacuum Brake Booster)  INSTALLATION  


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster assembly.


Hide 44610 2.INSTALL BRAKE BOOSTER ASSEMBLY

a.

Temporarily install the brake booster assembly to the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines.



b.

Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.

NOTICE:

Tighten the lock nut when adjusting the brake pedal height.



c.

Install the 4 nuts to secure the brake booster assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


d.

Install a new brake tube clamp to the vehicle body with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

C406562


e.

Engage the clamp and install a new brake tube clamp to the vehicle body.


f.
C406554C01
0.833,0.25 1,0.25 1,0.25 1.469,0.708 true 0.74,0.667 0.906,0.667 0.906,0.667 1.406,0.969 true 0.646,0.156 0.854,0.365 0.208,0.208 10 true *a 0.542,0.573 0.75,0.781 0.208,0.208 10 true *b
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly


Temporarily install each brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




g.
C406558

Engage the 3 clamps to connect the brake tube clamp to the brake lines.


h.
C406559

Engage the 5 clamps to install a new brake tube clamp to the brake lines.


i.
C406560

Engage the 5 clamps to install a new brake tube clamp to the brake lines.


j.
C406561

Engage the 5 clamps to connect the brake tube clamp to the brake lines.


k.
C409042C01
2.667,2.708 2.771,3.031 2.771,3.031 2.854,3.031 false 1.74,2.99 2.052,3.146 0.313,0.156 10 false *a 2.906,2.948 3.219,3.104 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 2 brake lines to the brake actuator assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




l.
C406553

w/ Stop and Start System:

i.

Connect the connector to the vacuum sensor assembly.



m.
C406552

Connect the connector to the vacuum warning switch assembly.


n.

Remove the protective tape.


o.
C406550N01
1.406,1.354 1.573,1.552 0.167,0.198 10 true A 2.292,0.688 2.458,0.885 0.167,0.198 10 true B

Engage the guide and connect the wire harness.


p.

Install the bolt (A) and nut (B) to secure the wire harness.

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Nut (B) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 44772 3.INSTALL CHECK VALVE TO CONNECTOR TUBE HOSE

a.
C409041C01
1.146,0.646 1.25,0.646 1.25,0.646 1.75,1.01 true 0.969,0.542 1.135,0.708 0.167,0.167 10 true *a
*a Paint Mark


Connect the check valve to connector tube hose to the brake booster assembly and slide the clip to secure it.

NOTICE:
·

When connecting the check valve to connector tube hose, face the paint mark up.

·

Make sure that the tabs of the clip are facing upward.




Hide 5.CONNECT WIRE HARNESS

a.
C406469

Engage the 2 clamps to connect the wire harness to the brake pedal support assembly.


b.

Connect the connector.


Hide 87211 7.INSTALL NO. 1 AIR DUCT

Hide 73900 8.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 47201 12.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY