Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2018.10–2019.02
RM3620E _55 Steering _076852 STEERING COLUMN _0377454 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45250 2.INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:
·

After the column is installed, check the tilt operation.

·

If a large amount of force is required to operate the tilt mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt operation works smoothly.

Tighten the nuts and check the tilt operation again.




b.

Connect each connector and engage each wire harness clamp to the steering column assembly.


Hide 45220 3.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C406892C01
1.615,0.573 1.052,0.469 1.052,0.469 1.625,0.5 true 0.844,0.365 1.01,0.552 0.167,0.188 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.


b.

Install the steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


d.
C406894

Tighten the clamp.


Hide 45253 4.INSTALL STEERING COLUMN HOLE COVER

a.
C406864

Install the steering column hole cover with the 2 clips.


b.

Install the clip.


c.

Return the floor carpet.


Hide 45220 5.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 6.INSTALL FRONT WHEEL LH (for LHD)

Hide 7.INSTALL FRONT WHEEL RH (for RHD)

Hide 87211A 8.INSTALL NO. 2 AIR DUCT (for LHD)

a.
C406862C01
1.729,0.198 1.99,0.406 0.26,0.208 10 false *a
*a View A
V100137

Front


Attach the 3 claws to install a new No. 2 air duct.


b.

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87211A 9.INSTALL NO. 2 AIR DUCT (for RHD)

a.
C406863C01
2.5,0.198 2.813,0.396 0.313,0.198 10 false *a
*a View A
V100137

Front


Attach the 3 claws to install a new No. 2 air duct.


b.

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 10.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.
C406856

Using pliers, support the band clamp while loosened and set the turn signal switch assembly with spiral cable sub-assembly.


b.
C406896C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly as shown in the illustration.


c.

Tighten the band clamp.


d.

Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 11.INSTALL UPPER STEERING COLUMN COVER

a.
C406854

Attach the 2 claws and 4 clips to connect the upper steering column cover.


b.
C406898C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the upper steering column cover.


Hide 45024 12.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

a.
C406900

Attach the 2 claws to install the lower steering column cover sub-assembly.


b.
C406848

Install the 3 screws.


Hide 55410C 13.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 73900 14.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55480D 15.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 55474B 17.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55606 18.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 67914B 20.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 21.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84306 22.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 23.CHECK STEERING WHEEL CENTER POINT

Hide 45100 24.INSTALL STEERING WHEEL ASSEMBLY

Hide 25.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 26.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 27.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 28.INSTALL DECK BOARD ASSEMBLY (for HV Model)