The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during steering column assembly removal/installation are shown below.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>PRECAUTION
for Gasoline Model with Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Gasoline Model with Occupant Classification System)>PRECAUTION
for HV Model with Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
58410B
3.REMOVE DECK BOARD ASSEMBLY (for HV Model)
58416K
4.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
65351A
5.REMOVE BATTERY HOLE COVER (for HV Model)
6.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FKS: Click hereGeneral>MAINTENANCE>A25A-FKS BATTERY>REMOVAL
for M20A-FKS: Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>REMOVAL
for A25A-FXS: Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67914B
7.REMOVE FRONT DOOR SCUFF PLATE LH
62112
8.REMOVE COWL SIDE TRIM BOARD LH
55606
9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55474B
10.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH
55545
11.REMOVE FUSE BOX OPENING COVER
for LHD: Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
for RHD: Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
55480D
12.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
73900
13.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
45100
14.REMOVE STEERING WHEEL ASSEMBLY
55410C
15.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
45287
16.REMOVE STEERING COLUMN LOWER COVER
Remove the 3 screws.
|
Place Hands Here |
|
Remove in this Direction |
While pressing the push area shown in the illustration to detach the 2 claws, slightly lower the lower steering column cover sub-assembly.
45286B
17.REMOVE STEERING COLUMN UPPER COVER
|
Remove in this Direction |
Detach the claw and separate the upper steering column cover.
Detach the 2 claws and 4 clips to remove the upper steering column cover.
18.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.
Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.
Using pliers, support the band clamp while loosened.
Detach the claw to remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.
87211A
19.REMOVE NO. 2 AIR DUCT (for LHD)
| *a | View A |
|
Front |
Remove the 2 bolts.
Detach the 3 claws to remove the No. 2 air duct.
Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 2 air duct.
87211A
20.REMOVE NO. 2 AIR DUCT (for RHD)
| *a | View A |
|
Front |
Remove the 2 bolts.
Detach the 3 claws to remove the No. 2 air duct.
Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 2 air duct.
21.REMOVE FRONT WHEEL LH (for LHD)
22.REMOVE FRONT WHEEL RH (for RHD)
45220
23.DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
45253
24.REMOVE STEERING COLUMN HOLE COVER
Turn back the floor carpet.
Remove the clip.
Detach the 2 clips to remove the steering column hole cover.
45220
25.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY
Using a screwdriver, loosen the clamp as shown in the illustration.
| *a | Matchmark |
Remove the bolt and slide the steering intermediate shaft assembly.
Do not remove the steering intermediate shaft assembly from the steering column assembly.
Put matchmarks on the steering intermediate shaft assembly and steering column assembly.
Remove the steering intermediate shaft assembly from the steering column assembly.
45250
26.REMOVE STEERING COLUMN ASSEMBLY
Disconnect each connector and disengage each wire harness clamp from the steering column assembly.
Remove the bolt, 2 nuts and steering column assembly.