82114
1.REMOVE NO. 4 ENGINE ROOM WIRE
Disconnect each connector.
| *A | w/ TOYOTA Parking Assist-sensor System | *B | w/ Panoramic View Monitor System |
| *C | w/ Dynamic Radar Cruise Control System | - | - |
Detach the clamp and remove the No. 4 engine room wire.
89341K
2.REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89341L
3.REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89347B
4.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
88211B
5.REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)
6.REMOVE NUT
|
Remove in this Direction |
Remove the 2 nuts.
52114A
7.REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET
for Type A:
Remove the 2 screws.
|
Remove in this Direction |
Detach the claw and guide to remove the front bumper extension mounting bracket as shown in the illustration.
for Type B:
Remove the 2 screws.
|
Remove in this Direction |
Detach the guide to remove the front bumper extension mounting bracket as shown in the illustration.
81220
8.REMOVE FOG LIGHT ASSEMBLY LH
81210A
9.REMOVE FOG LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
53395E
10.REMOVE FRONT HOOD TO END PANEL SEAL
|
Remove in this Direction |
Detach the clip and remove the front hood to end panel seal.
53115B
11.REMOVE RADIATOR GRILLE BRACKET
|
Screw |
|
Clip (A) |
|
Clip (B) |
Remove the 2 screws.
Remove the 4 clips (A).
Remove the 2 clips (B) and detach the guide.
|
Remove in this Direction |
Remove the 6 screws.
Detach the claw and remove the radiator grille bracket as shown in the illustration.
53112A
12.REMOVE LOWER RADIATOR GRILLE
Remove the 2 outside moulding retainers.
|
Remove in this Direction |
Detach the claw and guide to remove the lower radiator grille.
52128B
13.REMOVE FRONT BUMPER HOLE COVER LH
|
Remove in this Direction |
Detach the claw and remove the front bumper hole cover LH as shown in the illustration.
52127D
14.REMOVE FRONT BUMPER HOLE COVER RH
Use the same procedure as for the LH side.
75311
15.REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
|
Remove in this Direction |
Remove the 2 screws.
Detach the claw and guide and remove the radiator grille (or front panel) emblem as shown in the illustration.
53111
16.REMOVE RADIATOR GRILLE
52711
17.REMOVE FRONT BUMPER MOULDING
Remove the 4 clips.
Remove the 6 outside moulding retainers.
|
Remove in this Direction |
Detach the claw and guide and remove the front bumper moulding as shown in the illustration.
52411
18.REMOVE FRONT BUMPER GUARD
Remove the 4 outside moulding retainers.
Remove the 4 clips.
|
Remove in this Direction |
Detach the claw and guide to remove the front bumper guard as shown in the illustration.
53113E
19.REMOVE LOWER NO. 2 RADIATOR GRILLE
|
Remove in this Direction |
Remove the 4 screws.
Detach the claw to remove the lower No. 2 radiator grille as shown in the illustration.
53286C
20.REMOVE FRONT BUMPER ARM HOLE COVER LH
|
Remove in this Direction |
Detach the claw.
|
Fall Prevention Hook |
Detach the fall prevention hook and remove the front bumper arm hole cover LH.
53285J
21.REMOVE FRONT BUMPER ARM HOLE COVER RH
Use the same procedure as for the LH side.
52438
22.REMOVE FRONT BUMPER GUARD COVER LH
|
Remove in this Direction |
Detach the claw.
|
Fall Prevention Hook |
Detach the fall prevention hook and remove the front bumper guard cover LH.
52437
23.REMOVE FRONT BUMPER GUARD COVER RH
Use the same procedure as for the LH side.
24.REMOVE ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
When removing the ultrasonic sensor retainer, if the double-sided tape is difficult to remove, heat the adhesive of the ultrasonic sensor retainer and front bumper cover using a heat light.
| Item | Temperature |
|---|---|
| Front Bumper Cover | 20 to 30°C (68 to 86°F) |
| Ultrasonic Sensor Retainer | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the ultrasonic sensor retainer excessively.
Remove the ultrasonic sensor retainer.