Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (for Off Road Package) › 2018.10–2020.08
RM3620E _59 Vehicle Exterior _076404 EXTERIOR PANELS / TRIM _0377204 FRONT BUMPER(for Off Road Package) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(for Off Road Package)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

HINT:

When installing a new ultrasonic sensor retainer, heat the front bumper cover using a heat light.


Standard:
Item Temperature
Front Bumper Cover 20 to 30°C (68 to 86°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front bumper cover and ultrasonic sensor retainer excessively.


a.

When reusing the front bumper cover:

i.

Using a heat light, heat the front bumper cover surface.


ii.

Remove any remaining double-sided tape from the front bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front bumper cover with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

·

Also, clean a new front bumper cover surface.





b.
B498415C07
1.688,1.896 1.688,1.531 false 1.635,1.938 1.948,2.135 0.313,0.198 10 false *a
*a Mark-off Line
V100145

Primer


Apply primer to the front bumper cover on the installation area of the ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the ultrasonic sensor retainer has been attached.




c.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



d.

Remove the release paper of a new ultrasonic sensor retainer trying not to touch the adhesional surface.


e.
B525971C01
0.615,1.083 1.115,1.083 true 0.427,0.99 0.625,1.167 0.198,0.177 10 true *a
*a Mark-off Line


Install the ultrasonic sensor retainer in the position shown in the illustration.


Hide 52438 2.INSTALL FRONT BUMPER GUARD COVER LH

a.
B525969C01
0,0 0,0 false
V100135

Fall Prevention Hook


Attach the fall prevention hook.


b.
B525968C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the front bumper guard cover LH as shown in the illustration.


Hide 52437 3.INSTALL FRONT BUMPER GUARD COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 53286C 4.INSTALL FRONT BUMPER ARM HOLE COVER LH

a.
B525966C01
0,0 0,0 false
V100135

Fall Prevention Hook


Attach the fall prevention hook.


b.
B525965C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the front bumper arm hole cover LH as shown in the illustration.


Hide 53285J 5.INSTALL FRONT BUMPER ARM HOLE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 53113E 6.INSTALL LOWER NO. 2 RADIATOR GRILLE

a.
B526131C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the lower No. 2 radiator grille as shown in the illustration.


b.

Install the 4 screws.


Hide 52411 7.INSTALL FRONT BUMPER GUARD

a.
B526132C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the front bumper guard as shown in the illustration.


b.
B525962

Install the 4 outside moulding retainers.


c.

Install the 4 clips.


Hide 52711 8.INSTALL FRONT BUMPER MOULDING

a.
B525961C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the front bumper moulding as shown in the illustration.


b.
B525959

Install the 6 outside moulding retainers.


c.
B525958

Install the 4 clips.


Hide 75311 10.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

a.
B526129C02
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the radiator grille (or front panel) emblem as shown in the illustration.


b.

Install the 2 screws.


Hide 52128B 11.INSTALL FRONT BUMPER HOLE COVER LH

a.
B526127C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the front bumper hole cover LH as shown in the illustration.


Hide 52127D 12.INSTALL FRONT BUMPER HOLE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 53112A 13.INSTALL LOWER RADIATOR GRILLE

a.
B525544C02
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the lower radiator grille.


b.
B526124

Install the 2 outside moulding retainers.


Hide 53115B 14.INSTALL RADIATOR GRILLE BRACKET

a.
B526123C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the radiator grille bracket as shown in the illustration.


b.

Install the 6 screws.


c.
B526121C01
0,0 0,0 false
V100135

Screw
V100136

Clip (A)
V100137

Clip (B)


Install the 2 clips (B) and attach the guide.


d.

Install the 4 clips (A).


e.

Install the 2 screws.


Hide 53395E 15.INSTALL FRONT HOOD TO END PANEL SEAL

a.
B526120C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and install the front hood to end panel seal.


Hide 81220 16.INSTALL FOG LIGHT ASSEMBLY LH

Hide 81210A 17.INSTALL FOG LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 52114A 18.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET

a.

for Type A:

i.
B525557C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide to install the front bumper extension mounting bracket as shown in the illustration.


ii.
B525560

Install the 2 screws.



b.

for Type B:

i.
B525559C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide to install the front bumper extension mounting bracket as shown in the illustration.


ii.
B525561

Install the 2 screws.



Hide 19.INSTALL NUT

a.
B526117C01
0,0 0,0 false
V113147

Install in this Direction


Install the 2 nuts.


Hide 88211B 20.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

Hide 89347B 21.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89341L 22.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89341K 23.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 82114 24.INSTALL NO. 4 ENGINE ROOM WIRE

a.

Attach the clamp and install the No. 4 engine room wire.

B526114C01
1.917,2.188 1.917,1.688 true 5.156,2.208 5.156,1.708 true 3.177,1.667 3.177,1.167 true 0.583,2.792 0.833,3.01 0.25,0.219 12 true *A 2.167,2.083 2.417,2.302 0.25,0.219 12 true *A 4.781,2.063 5.031,2.281 0.25,0.219 12 true *A 6.385,2.771 6.635,2.99 0.25,0.219 12 true *A 3.469,1.99 3.719,2.208 0.25,0.219 12 true *B 3.865,1.24 4.115,1.458 0.25,0.219 12 true *C 1.802,2.188 2.052,2.406 0.25,0.219 12 true *A 5.063,2.198 5.313,2.417 0.25,0.219 12 true *A 2.917,1.635 3.448,1.823 0.531,0.188 12 true *C,*B
*A w/ TOYOTA Parking Assist-sensor System *B w/ Panoramic View Monitor System
*C w/ Dynamic Radar Cruise Control System - -



b.

Connect each connector.