Use the same procedure for the RH and LH sides.
The procedure below is for the LH side.
69780E
1.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
|
Install in this Direction |
Attach the clamp and install the rear door inside locking cable assembly as shown in the illustration.
69740E
2.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
|
Install in this Direction |
Attach the clamp and install the rear door lock remote control cable assembly as shown in the illustration.
69038A
3.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY LH (w/o Double Locking System)
Attach the claw.
|
Install in this Direction |
Attach the claw and install the rear door lock cover sub-assembly LH as shown in the illustration.
69318D
4.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/o Double Locking System)
When reusing the removed rear door lock with motor assembly LH, be sure to replace the door lock wiring harness seal on the connector with a new one.
Keep the door lock wiring harness seal of the connector free from grease and dust, etc.
Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water to enter the connecting part. This may result in a malfunction of the rear door lock with motor assembly LH.
When reusing rear door lock with motor assembly LH:
Install a new door lock wiring harness seal to the rear door lock with motor assembly LH.
69060A
5.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)
Apply MP grease to the sliding parts of the rear door lock with motor assembly LH.
| *a | Release Plate |
|
Install in this Direction |
Connect the rear door lock with motor assembly LH to the release plate of the rear door outside handle frame sub-assembly LH, and set it to the rear door panel.
Make sure that the release plate of the rear door outside handle frame sub-assembly LH is securely connected to the rear door lock with motor assembly LH.
Using a T30 "TORX" socket wrench, install the front door lock with motor assembly LH with the 3 "TORX" screws.
69780E
6.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
|
Install in this Direction |
Attach the clamp and install the rear door inside locking cable assembly as shown in the illustration.
|
Install in this Direction |
Attach the claw and install the cover as shown in the illustration.
69740E
7.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
|
Install in this Direction |
Attach the clamp and install the rear door lock remote control cable assembly as shown in the illustration.
|
Install in this Direction |
Attach the claw and install the cover as shown in the illustration.
69318D
8.INSTALL DOOR LOCK WIRING HARNESS SEAL (w/ Double Locking System)
When reusing the removed rear door lock with motor assembly LH, be sure to replace the door lock wiring harness seal on the connector with a new one.
Keep the door lock wiring harness seal of the connector free from grease and dust, etc.
Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water to enter the connecting part. This may result in a malfunction of the rear door lock with motor assembly LH.
When reusing rear door lock with motor assembly LH:
Install a new door lock wiring harness seal to the rear door lock with motor assembly LH.
69060A
9.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)
Apply MP grease to the sliding parts of the rear door lock with motor assembly LH.
| *a | Release Plate |
|
Install in this Direction |
Connect the rear door lock with motor assembly LH to the release plate of the rear door outside handle frame sub-assembly LH, and set it to the rear door panel.
Make sure that the release plate of the rear door outside handle frame sub-assembly LH is securely connected to the rear door lock with motor assembly LH.
Using a T30 "TORX" socket wrench, install the front door lock with motor assembly LH with the 3 "TORX" screws.
69804
10.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
68104
11.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
67408E
12.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
68152C
13.INSTALL REAR DOOR GLASS RUN LH
67674A
14.INSTALL REAR DOOR FRAME GARNISH LH
67842E
15.INSTALL REAR DOOR SERVICE HOLE COVER LH
68199
16.INSTALL REAR DOOR REAR BELT SEAL LH
68197A
17.INSTALL REAR DOOR FRONT BELT SEAL LH
68174A
18.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH
67604
19.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
20.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
74646A
21.INSTALL DOOR ASSIST GRIP COVER LH
69278C
22.INSTALL REAR DOOR INSIDE HANDLE BEZEL LH
23.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>INSTALLATION
for A25A-FKS:
for M20A-FKS:
Click hereGeneral>MAINTENANCE>M20A-FKS BATTERY>INSTALLATION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65351A
24.INSTALL BATTERY HOLE COVER (for HV Model)
58416K
25.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)
58410B
26.INSTALL DECK BOARD ASSEMBLY (for HV Model)
27. INITIALIZE POWER WINDOW CONTROL SYSTEM
28. CHECK POWER WINDOW CONTROL SYSTEM
29. CHECK POWER DOOR LOCK CONTROL SYSTEM