This DTC is output when an open circuit or short occurs in the communication line between a front center ultrasonic sensor (FLC sensor) and the front corner ultrasonic sensor (FL sensor), or when a malfunction occurs in a front center ultrasonic sensor (FLC sensor) on the front.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AE287 | Ultrasonic Sensor (Front Left Center) Missing Message | Front center ultrasonic sensor (FLC sensor) lost communication | ·
Front center ultrasonic sensor (FLC sensor) ·
Harness or connector ·
Clearance warning ECU assembly |
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
If a DTC is detected again after the repair, turn the engine switch on (IG) and turn the TOYOTA parking assist-sensor system on, and then clear the DTC.
If C1AE196 is output at the same time, check C1AE196 first.
Initialize the front corner ultrasonic sensors (FL and FR sensors) and front center ultrasonic sensors (FLC and FRC sensors).
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Clear the DTCs.
Recheck for DTCs.
| Symptoms | DTC Detection | |||
|---|---|---|---|---|
| C1AE187 | C1AE287 | C1AE387 | C1AE487 | |
| Symptom 1 | Not output | Not output | Not output | Not output |
| Symptom 2 | Not output | Not output | Not output | Output |
| Symptom 3 | Not output | Not output | Output | Output |
| Symptom 4 | Not output | Output | Output | Output |
| Symptom 5 | Output | Output | Output | Output |
| Result | Proceed to |
|---|---|
| Listed under symptom 1 in combination table | A |
| Listed under symptom 2 in combination table | B |
| Listed under symptom 3 in combination table | C |
| Listed under symptom 4 in combination table | D |
| Listed under symptom 5 in combination table | E |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
E
Disconnect the B5 front corner ultrasonic sensor (FL sensor) connector.
Disconnect the B4 front center ultrasonic sensor (FLC sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B5-1 (BO) - B4-4 (BI) | Always | Below 1 Ω |
| B5-2 (SO) - B4-5 (SI) | Always | Below 1 Ω |
| B5-3 (EO) - B4-6 (EI) | Always | Below 1 Ω |
| B5-1 (BO) or B4-4 (BI) - Body ground | Always | 10 kΩ or higher |
| B5-2 (SO) or B4-5 (SI) - Body ground | Always | 10 kΩ or higher |
| B5-3 (EO) or B4-6 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front center ultrasonic sensor (FLC sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Inspect the front center ultrasonic sensor (FLC sensor).
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
Replace the front center ultrasonic sensor (FLC sensor) with a known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR (for Front)>REMOVAL
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC C1AE287 is output | B |
A
B
for LHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD:
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL