Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377029 BRAKE SYSTEM(w/o Vacuum Brake Booster) G

BRAKE SYSTEM (OTHER)  BRAKE SYSTEM(w/o Vacuum Brake Booster)  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

DTCs may be stored during the inspection procedure. Be sure to clear the DTCs and check that no DTCs are output after the inspection is finished.


PROCEDURE

Hide 1.INSPECT PRESSURE SENSOR

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Set a pedal effort gauge, SST and connect the GTS.

i.
C409088C01
0.615,0.365 0.875,0.365 false 1.698,0.354 1.948,0.354 false 2.531,0.365 2.771,0.365 false 0.365,2.854 0.417,2.854 0.417,2.854 0.417,3.104 false 3.063,2.938 3.083,3.156 3.083,3.156 3.146,3.156 false 2.042,0.25 2.354,0.406 0.313,0.156 10 false *a 2.344,0.281 2.656,0.438 0.313,0.156 10 false *b 0.167,2.76 0.479,2.917 0.313,0.156 10 false *c 3.198,3.052 3.417,3.24 0.219,0.188 10 false *c 0.906,0.281 1.219,0.438 0.313,0.156 10 false *b
*a Pedal Effort Gauge
*b SST (LSPV Gauge)
*c SST (No. 1 Nipple)


Set a pedal effort gauge and SST.

SST
09709-29018  (09709-00060, 09709-00080)


ii.

Connect the GTS to the DLC3 with the power switch off, park (P) selected and parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.




c.

Inspect the wheel cylinder pressure sensor and regulator pressure sensor.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test / Power Supply Air Bleeding Pattern 1.

Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Power Supply Air Bleeding Pattern1
Data List Display
Regulator Pressure Sensor Output
Wheel Cylinder Pressure Sensor
50004 105 62 307,308

ii.

Select "Wheel Cylinder Pressure Sensor" and "Regulator Pressure Sensor Output".


iii.

Check the value output from "Wheel Cylinder Pressure Sensor" and "Regulator Pressure Sensor Output" by depressing the brake pedal.

Standard Result:
Pedal Effort Regulator Pressure Sensor Output
(V)
Rear Right Wheel Hydraulic Pressure Rear Left Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.60 to 1.40 0.46 to 4.46 MPa (4.7 to 45.4 kgf/cm2, 67 to 646 psi) 0.46 to 4.46 MPa (4.7 to 45.4 kgf/cm2, 67 to 646 psi)
100 N (10 kgf, 22.5 lbf) 1.60 to 2.40 5.33 to 9.33 MPa (54.4 to 95.1 kgf/cm2, 773 to 1352 psi) 5.33 to 9.33 MPa (54.4 to 95.1 kgf/cm2, 773 to 1352 psi)
150 N (15 kgf, 33.7 lbf) 2.59 to 3.39 10.19 to 14.19 MPa (104.0 to 144.6 kgf/cm2, 1478 to 2057 psi) 10.19 to 14.19 MPa (104.0 to 144.6 kgf/cm2, 1478 to 2057 psi)
200 N (20 kgf, 45.0 lbf) 3.58 to 4.38 15.06 to 19.06 MPa (153.6 to 194.3 kgf/cm2, 2184 to 2763 psi) 15.06 to 19.06 MPa (153.6 to 194.3 kgf/cm2, 2184 to 2763 psi)


Standard Result:
Pedal Effort Wheel Cylinder Pressure Sensor
(V)
Front Right Wheel Hydraulic Pressure Front Left Wheel Hydraulic Pressure
50 N (5 kgf, 11.2 lbf) 0.53 to 1.33 0.11 to 4.11 MPa (1.2 to 41.9 kgf/cm2, 16 to 595 psi) 0.11 to 4.11 MPa (1.2 to 41.9 kgf/cm2, 16 to 595 psi)
100 N (10 kgf, 22.5 lbf) 1.38 to 2.18 4.27 to 8.27 MPa (43.6 to 84.3 kgf/cm2, 620 to 1199 psi) 4.27 to 8.27 MPa (43.6 to 84.3 kgf/cm2, 620 to 1199 psi)
150 N (15 kgf, 33.7 lbf) 2.23 to 3.03 8.44 to 12.44 MPa (86.1 to 126.8 kgf/cm2, 1224 to 1803 psi) 8.44 to 12.44 MPa (86.1 to 126.8 kgf/cm2, 1224 to 1803 psi)
200 N (20 kgf, 45.0 lbf) 3.07 to 3.87 12.57 to 16.57 MPa (128.2 to 168.9 kgf/cm2, 1823 to 2402 psi) 12.57 to 16.57 MPa (128.2 to 168.9 kgf/cm2, 1823 to 2402 psi)



iv.

After inspection, turn "Power Supply Air Bleeding Pattern 1" off.



d.

Remove the pedal effort gauge and SST.

i.

Remove the pedal effort gauge and SST, and bleed brake line.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (w/o Vacuum Brake Booster)>BLEEDING



e.

Inspect the accumulator sensor.

i.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Accumulator Sensor.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Sensor
50003 105 13

ii.

Depress the brake pedal 4 or 5 times and operate the booster pump motor.


iii.

After confirming that the booster pump motor stops, check the output voltage.

Standard Voltage:

2.9 to 4.2 V




Hide 47210L 2.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Connect the GTS and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the GTS to the DLC3 with the power switch off, park (P) selected and parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.




c.

Check operation without the brake booster.


ii.
C400747C04
2.708,1.646 3.042,1.646 true 2.552,3.938 2.719,3.938 true 2.417,4.146 2.75,4.146 true 2.438,1.417 2.604,1.417 true 0,0 0.219,0.198 0.219,0.198 10 true *A 0,2.625 0.229,2.802 0.229,0.177 10 true *B 2.219,1.292 2.458,1.49 0.24,0.198 10 true *a 3.073,1.542 3.302,1.74 0.229,0.198 10 true *b 2.313,3.813 2.552,4.01 0.24,0.198 10 true *a 2.229,4.042 2.458,4.24 0.229,0.198 10 true *b
*A for LHD
*B for RHD
*a Fluid Level Support Line
*b MIN Line


Adjust the brake fluid level in the reservoir between MIN line and fluid level support line.


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB (Electronically Controlled Brake system) Utility / Zero Down.

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167
NOTICE:

Go to the next step without turning the power switch off.



iv.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Wheel Cylinder Pressure Sensor, Stroke Sensor and Stroke Sensor 2.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
Wheel Cylinder Pressure Sensor
50003 105 11,12,308

v.

Check the values output from "Wheel Cylinder Pressure Sensor", "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage:
Pedal Effort Wheel Cylinder Pressure Sensor
(V)
Stroke Sensor
(V)
Stroke Sensor 2
(V)
200 N (20 kgf, 45.0 lbf) 0.52 to 1.32 1.19 to 1.89 3.11 to 3.81
500 N (51 kgf, 112.4 lbf) 1.16 to 1.96 1.51 to 2.21 2.79 to 3.49



vi.

Turn the power switch off to finish "Zero Down".


vii.

Turn the power switch on (IG) and wait for 20 seconds, then enter the following menus: Chassis / ABS/VSC/TRC / Data List / Accumulator Sensor, and check the output voltage.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Sensor
50003 105 13
Standard Voltage:

2.9 to 4.2 V




Hide 3.INSPECT STROKE SIMULATOR

a.

Check auxiliary battery voltage.

Standard Voltage:

11 to 14 V (while the power switch is off)



b.

Connect the GTS and set a pedal effort gauge.

i.

Set a pedal effort gauge.


ii.

Connect the GTS to the DLC3 with the power switch off, park (P) selected and parking brake applied.


iii.

Turn the power switch on (IG) and turn the GTS on.




c.

Check operation with the brake booster.

i.

Turn the power switch on (IG).


ii.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor and Stroke Sensor 2.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
Stroke Sensor2
50003 105 11,12

iii.

Depress the brake pedal 4 or 5 times.


iv.

Check the values output from "Stroke Sensor" and "Stroke Sensor 2" by depressing the brake pedal.

Standard Voltage:
Pedal Effort Stroke Sensor
(V)
Stroke Sensor 2
(V)
50 N (5 kgf, 11.2 lbf) 1.37 to 2.07 2.93 to 3.63
100 N (10 kgf, 22.5 lbf) 1.66 to 2.36 2.64 to 3.34
150 N (15 kgf, 33.7 lbf) 1.83 to 2.53 2.47 to 3.17