Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for RHD without Vacuum Brake Booster)
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377036 BRAKE PEDAL(for RHD without Vacuum Brake Booster) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for RHD without Vacuum Brake Booster)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

b.

Check the brake pedal height.

HINT:

Perform checks and adjustments with the service hole carpet rolled back.


i.

Measure the shortest distance between the brake pedal pad surface and front floor footrest as shown in the illustration.

C410930C01
4.958,2.323 5.125,2.323 5.125,2.323 5.667,1.948 true 1.552,1.083 1.302,1.417 1.302,1.417 1.135,1.417 true 5.927,1.052 6.115,0.802 6.115,0.802 6.281,0.802 true 2.708,2 3.063,2.271 3.063,2.271 3.229,2.271 true 6.469,1.844 6.781,2 0.313,0.156 10 false *a 6.344,0.729 6.656,0.885 0.313,0.156 10 false *1 2.698,1.313 2.906,1.49 0.208,0.177 10 true *a 4.75,2.229 4.948,2.406 0.198,0.177 10 true *b 0.885,1.323 1.135,1.563 0.25,0.24 10 true *1 3.333,2.156 3.531,2.333 0.198,0.177 10 true *b
*1 Brake Pedal Pad - -
*a Brake Pedal Height *b Measuring Plane of Floor Panel
V100144

Service Hole - -


Brake Pedal Height from Floor Panel:

161.3 to 177.3 mm (6.36 to 6.98 in.)


If the brake pedal height is not as specified, inspect and adjust the push rod length according to the procedure below.



c.

Adjust the push rod length.

i.
C409093C01
0.958,3.927 1.719,3.927 true 2.146,1.76 2.344,1.948 2.344,1.948 2.625,1.948 true 1.167,2.135 1.167,1.875 1.167,1.875 1.333,1.51 true 1.115,2.208 1.323,2.375 0.208,0.167 10 true *1 2.677,1.896 2.99,2.052 0.313,0.156 10 false *2 0.76,3.865 1.073,4.021 0.313,0.156 10 false *3 2.729,3.802 3.042,3.958 0.313,0.156 10 false *a
*1 Lock Nut
*2 Stop Light Switch Assembly
*3 Floor Panel
*a Brake Pedal Height


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Loosen the lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Brake Pedal Height from Floor Panel:

161.3 to 177.3 mm (6.36 to 6.98 in.)



iv.

Tighten the lock nut.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


v.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION




Hide 89510D 2.INSPECT AND ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.

Inspect the brake pedal stroke sensor assembly.

i.

Connect the GTS to the DLC3 with the power switch off.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on and enter the following menus: Chassis / ABS/VSC/TRC / Data List / Stroke Sensor.

Chassis > ABS/VSC/TRC > Data List
Tester Display
Stroke Sensor
50003 105 11

iv.

Read the stroke sensor value without the brake pedal depressed.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V


If the stroke sensor value is not within the standard voltage, adjust the brake pedal stroke sensor assembly.



b.

Adjust the brake pedal stroke sensor assembly.

i.

Remove the front door scuff plate RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL



ii.

Remove the cowl side trim board RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL



iii.

Remove the No. 1 instrument panel under cover sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


iv.
C376568

Loosen the 2 nuts.

NOTICE:

Do not depress the brake pedal after turning the power switch on (IG).



v.
C408246

Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



vi.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


vii.

Perform initialization and calibration of linear solenoid valve and zero point of yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


viii.

Turn the GTS off and turn the power switch off.


ix.

Disconnect the GTS.


x.

Install the No. 1 instrument panel under cover sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION


xi.

Install the cowl side trim board RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION



xii.

Install the front door scuff plate RH.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION




Hide 3.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708C09
2.167,1.563 2.469,1.781 0.302,0.219 10 false *a
*a Brake Pedal Free Play


Depress the brake pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

Brake Pedal Free Play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the brake pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the brake pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 4.INSPECT BRAKE PEDAL RESERVE DISTANCE

a.

With the engine running, depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.

HINT:

Perform checks with the service hole carpet rolled back.


C409095C01
4.594,1.844 4.771,1.844 4.771,1.844 4.917,1.646 true 5.375,1.125 5.604,0.875 5.604,0.875 5.792,0.875 true 1.271,1.208 1.448,1.208 1.448,1.208 1.927,1.469 true 2.938,1.604 3.115,1.76 0.177,0.156 10 true *a 4.385,1.74 4.708,2.031 0.323,0.292 10 false *b 5.885,0.802 6.198,0.958 0.313,0.156 10 false *1 5.208,1.531 5.521,1.688 0.313,0.156 10 false *a 1.01,1.115 1.271,1.313 0.26,0.198 10 true *1
*1 Brake Pedal Pad - -
*a Brake Pedal Reserve Distance *b Measuring Plane of Floor Panel
V100144

Service Hole - -


Brake Pedal Reserve Distance from Floor Panel at 300 N (30.5 kgf, 67.4 lbf):

140 mm (5.52 in.) or more


If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM (w/o Vacuum Brake Booster)>PROBLEM SYMPTOMS TABLE