The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.
Inspect the fuses for circuits related to this system before performing the following procedure.
After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.
When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (brake warning switch assembly)*1 or electric parking brake switch (integration control and panel assembly)*2 as the parking brake indicator light blinks when the ignition switch is first turned to ON.
*1: for Manual Transaxle
*2: except Manual Transaxle
Even if the electric parking brake is operating normally, the parking brake indicator light on the combination meter may be malfunctioning.
Check if CAN communication system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| Lock and release operation is normal and parking brake indicator light turns off or blinks | A |
| Lock and release operation is malfunctioning and parking brake indicator light illuminates or turns off according to switch operation | B |
| Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks | C |
A
B
C
Perform the Active Test of the combination meter assembly using the GTS.
| Tester Display |
|---|
| Park Warning |
Check the combination meter assembly.
Parking brake indicator light turns on or off in accordance with the GTS operation.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD with Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD with Vacuum Brake Booster)>REMOVAL
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-30 (+BS) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-36 (IG1) - Body ground | Ignition switch ON | 10.5 to 16 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-36 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG (w/ Stop and Start System) |
| NG (w/o Stop and Start System) |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD with Vacuum Brake Booster)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD with Vacuum Brake Booster)>REMOVAL
NG (w/ Stop and Start System)
NG (w/o Stop and Start System)
Turn the ignition switch off.
Disconnect the A39 skid control ECU (brake actuator assembly) connector.
Disconnect the A32*1 or G62*2 engine stop and start ECU connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-36 (IG1) - A32-1 (IG31) | Always | Below 1 Ω |
| A39-36 (IG1) or A32-1 (IG31) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-36 (IG1) - G62-1 (IG31) | Always | Below 1 Ω |
| A39-36 (IG1) or G62-1 (IG31) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for A25A-FKS: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM (for A25A-FKS)>Backup Boost Converter Circuit
for M20A-FKS: Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for M20A-FKS)>Backup Boost Converter Circuit
NG