Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD with Vacuum Brake Booster) › 2018.10–2020.08
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0376836 BRAKE ACTUATOR(for RHD with Vacuum Brake Booster) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD with Vacuum Brake Booster)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:
(Click here)
for M20A-FKS:
(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of brake actuator assembly Operate the electric parking brake switch assembly Parking brake indicator light blinks when the engine switch is first turned on (IG) (Click here)
Perform acceleration sensor zero point calibration and store system information
·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.


Hide 2.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

HINT:

Use the same procedure as for LHD.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


Hide 55704B 4.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 8.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C407935C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C407936C01
1.698,0.958 1.219,0.281 1.219,0.281 1.01,0.281 true 0.813,1.542 0.885,1.542 0.885,1.542 1.396,1.177 true 0.781,0.625 0.854,0.625 0.854,0.625 1.552,1.063 true 1.958,1.156 2.552,1.583 2.552,1.583 2.719,1.583 true 1.49,1.969 1.594,1.969 1.594,1.969 1.688,1.385 true 1.844,0.885 2.438,0.594 2.438,0.594 2.542,0.594 true 2.76,1.5 2.927,1.667 0.167,0.167 10 true *a 1.292,1.896 1.469,2.063 0.177,0.167 10 true *b 2.604,0.5 2.781,0.667 0.177,0.167 10 true *c 0.813,0.198 0.979,0.365 0.167,0.167 10 true *d 0.552,0.531 0.75,0.729 0.198,0.198 10 true *e 0.583,1.427 0.75,1.594 0.167,0.167 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Front Wheel Cylinder Assembly LH


Use tags or make a memo to identify the places to reconnect the brake lines.


c.
C407937

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




d.

Disengage the 5 clamps to remove the brake tube clamps from the brake lines.


e.
C407930

Disengage the clamp to separate the brake line from the brake tube clamp.


f.
C407931

for Manual Transaxle:

i.

Disengage the clamp to separate the clutch master cylinder to flexible hose tube from the clutch master cylinder tube clamp.



g.
C407932

Remove the 2 bolts, nut and brake actuator with bracket.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



h.
C407933

Disengage the clamp to remove the brake tube clamp from the brake actuator bracket assembly.


i.
C407934

for Manual Transaxle:

i.

Disengage the clamp to remove the clutch master cylinder tube clamp from the brake actuator bracket assembly.



Hide 44510 9.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C407941

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44547B 10.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.
C407942C03
0.302,0.854 0.594,0.854 true 0.354,1.177 0.646,1.177 true 2.521,1.635 2.781,1.635 true 2.844,0.75 3.104,0.75 true 2.875,0.448 3.115,0.448 true 2.542,1.354 2.792,1.354 true 0.135,1.094 0.448,1.25 0.313,0.156 10 false *1 0.115,0.781 0.427,0.938 0.313,0.156 10 false *2 2.875,1.573 3.188,1.729 0.313,0.156 10 false *1 3.177,0.677 3.427,0.854 0.25,0.177 10 false *1 3.188,0.385 3.396,0.552 0.208,0.167 10 false *2 2.875,1.281 3.188,1.438 0.313,0.156 10 false *2
*1 No. 1 Brake Actuator Case Collar
*2 Brake Actuator Bracket Cushion


Remove the 3 nuts and separate the brake actuator bracket assembly.


b.

Remove the 3 No. 1 brake actuator case collars from the brake actuator bracket cushion.


c.

Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.