Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1234  Yaw Rate Sensor  C1243  Deceleration Sensor Stuck  C1244  Open or Short Circuit in Deceleration Sensor Circuit  C1245  Abnormal Output in Deceleration Sensor  C1279  Abnormal Output Voltage in Deceleration Sensor  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition using 2 circuits (GL1, GL2).

If there are malfunctions in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) will be stored.

These DTCs are also output when zero point calibration has not been completed.

DTC C1279 will be cleared when the yaw rate and acceleration sensor (airbag sensor assembly) sends a yaw rate and/or acceleration signal or when Test Mode ends. DTC C1279 is output only in Test Mode.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1234 Yaw Rate Sensor 711
712
713
714
·

INF Code: 711

-

While yaw rate sensor communication is enabled, a malfunction signal is received during the sensor self-check (Sensor 1 (GL1) malfunction).


·

INF Code: 712

-

While yaw rate sensor communication is enabled, a malfunction signal is received during the sensor self-check (Sensor 2 (GL2) malfunction).


·

INF Code: 713

-

While yaw rate sensor communication is enabled, a malfunction signal is received during the sensor self-check (Zero point calibration malfunction).


·

INF Code: 714

-

While yaw rate sensor communication is enabled, a malfunction signal is received during the sensor self-check (Two-value comparison malfunction).



Yaw rate sensor (Airbag sensor assembly) internal malfunction -
C1243 Deceleration Sensor Stuck 561
562
563
564
565
·

INF Code: 561

-

An acceleration sensor malfunction occurs 16 times or more when the vehicle speed drops from above 30 km/h (19 mph) to 0 km/h (0 mph).


·

INF Code: 562, 563, 564, 565

-

A stuck acceleration sensor value is determined.



Acceleration sensor (Airbag sensor assembly) internal stuck malfunction -
C1244 Open or Short Circuit in Deceleration Sensor Circuit 571 A malfunction signal from the acceleration sensor is received.
·

Acceleration sensor (Airbag sensor assembly) installed improperly

·

Acceleration sensor (Airbag sensor assembly)


-
C1245 Abnormal Output in Deceleration Sensor 581 At a vehicle speed of 30 km/h (19 mph) or more, difference between longitudinal G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Acceleration sensor (Airbag sensor assembly) installed improperly

·

Acceleration sensor (Airbag sensor assembly)


-
C1279 Abnormal Output Voltage in Deceleration Sensor - Detected only during Test Mode.
·

Sensor installation

·

Acceleration sensor (Airbag sensor assembly)


-

CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


HINT:

When U0123 and/or U0124 is output together with C1234, C1243, C1244, and/or C1245, inspect and repair the trouble areas indicated by U0123 and/or U0124 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>U0073


PROCEDURE

1.CHECK DTC

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Drive the vehicle at a speed of 30 km/h (19 mph) or more, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Turn the power switch on (IG) again and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM


f.

Check if DTC C1210 (Zero Point Calibration of Yaw Rate Sensor Undone) or C1336 (Zero Point Calibration of Acceleration Sensor Undone) is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs (C1210, C1336 and CAN communication system DTCs) are not output. A
CAN communication system DTCs are output. B
DTCs C1210 and/or C1336 are output. C



A

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION

B

C

2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the power switch off.


b.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The airbag sensor assembly is tightened to the specified torque.

The airbag sensor assembly is not tilted.


NOTICE:

Check the yaw rate and acceleration sensor (airbag sensor assembly) signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG