Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)
RM3620E _54 Brake _076410 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0379312 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(w/o Vacuum Brake Booster)  C1202  Master Reservoir Level Malfunction  


DESCRIPTION

When a fluid level drop in the brake master cylinder reservoir assembly is detected, a signal is sent to the skid control ECU (brake booster with master cylinder assembly).

If a DTC for the fluid level drop is stored, the warning will be canceled and the DTC will be cleared when the fluid level returns to normal.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1202 Master Reservoir Level Malfunction 371
-
·

INF Code: 371

-

An open is detected in the switch signal circuit for 2 seconds or more.


·

INF Code: -

-

The reservoir level remains low.



·

INF Code: 371

-

Brake fluid level warning switch (Brake master cylinder reservoir assembly) internal open circuit


-

Open in wire harness


-

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: -

-

Low brake fluid level


-

Brake fluid leaks


-

Brake fluid level warning switch (Brake master cylinder reservoir assembly) internal short circuit


-

Short in wire harness


-

Brake disc rotor excessive wear


-

Skid control ECU (Brake booster with master cylinder assembly)



-

WIRING DIAGRAM

C325433E12
2.177,2.115 4.24,2.677 2.063,0.563 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 4.031,1.229 4.135,1.385 0.104,0.156 10 false 1 1.708,2.073 2.104,2.417 0.396,0.344 10 false A4*1 2,1.188 2.292,1.479 0.292,0.292 10 false 2 5.094,1.208 5.51,1.521 0.417,0.313 10 false 36 5.042,3.021 7.104,3.49 2.063,0.469 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.417,1.219 5.865,1.5 0.448,0.281 10 false LBL 4.708,2.979 5.104,3.313 0.396,0.333 10 false A42 3.76,1.229 3.958,1.458 0.198,0.229 10 false + 2.281,1.177 2.479,1.458 0.198,0.281 10 false E 1.677,2.302 2.073,2.646 0.396,0.344 10 false A20*2 1.24,2.969 2.208,3.281 0.969,0.313 10 false *1: for LHD 1.25,3.344 2.115,3.583 0.865,0.24 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>UTILITY


HINT:

Before releasing the parking brake, chock the wheels for safety.


PROCEDURE

1.CHECK BRAKE FLUID LEVEL
a.

Check that the brake fluid level is sufficient.

OK:

Brake fluid level is sufficient.


HINT:

If the fluid level is low, check for fluid leaks, and repair as necessary.


i.

Check for brake fluid leaks (connection between the brake booster pump assembly, brake master cylinder reservoir assembly and brake booster with master cylinder assembly, and the brake booster with master cylinder assembly and wheel cylinders).

HINT:

If no leaks exist, add and adjust fluid using the GTS.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (w/o Vacuum Brake Booster)>ON-VEHICLE INSPECTION



ii.

Check that the DTC is not output again.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105


b.

Check that there are no leaks from the connections between the brake booster pump assembly and brake booster with master cylinder assembly.

HINT:

As a visual check is very difficult, perform the check with the following procedure.


i.

ii.

Connect the GTS to the DLC3.


iii.

Turn the power switch on (IG).


iv.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor Min.: 0.00 V, Max.: 5.00 V Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
Chassis > ABS/VSC/TRC > Data List
Tester Display
Accumulator Sensor
50003 105 13

v.

Depress the brake pedal 4 or 5 times to operate the pump motor.


vi.

Wait for 30 seconds without depressing the brake pedal.


vii.

Check that the accumulator pressure sensor output value change is within the specified range.

OK:

Accumulator pressure sensor output value change is less than 0.55 V.




Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

2.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

OK (for RHD)

7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

NG

CHECK AND REPAIR BRAKE FLUID LEAKS OR ADD FLUID

2.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.
C409032C01
1.542,1.854 0.875,2.885 false 2,1.896 2.656,2.927 false 0.781,2.917 1.063,3.198 0.281,0.281 10 E 2.646,2.938 2.885,3.167 0.24,0.229 10 + 0.375,0.354 0.688,0.51 0.313,0.156 10 *a
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Turn the power switch off.


b.

Remove the reservoir filler cap.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the A4 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (E) Brake fluid level warning switch off (float up) 1.84 to 2.16 kΩ
1 (+) - 2 (E) Brake fluid level warning switch on (float down) Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-36 (LBL) - A4-1 (+) Always Below 1 Ω
A42-36 (LBL) or A4-1 (+) - Body ground Always 10 kΩ or higher
A4-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SWITCH INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SWITCH INPUT)
a.
C409033C01
0.427,1.083 0.813,1.333 0.385,0.25 1.375,1.99 0.885,2.531 false 0.542,1.125 1.135,1.469 0.594,0.344 10 false A4 0.729,2.448 0.917,2.677 0.188,0.229 10 false + 0.333,0.344 0.646,0.5 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-1 (+) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK BRAKE DISC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

5.CHECK BRAKE DISC
a.

Turn the power switch off.


b.

Reconnect the A4*1 or A20*2 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.

*1: for LHD

*2: for RHD



c.

Disconnect the A41 brake pedal stroke sensor assembly connector.


d.

Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper pistons and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.

·

Uneven disc wear can be checked by measuring the disc thickness variation.

for Front Brake (for 2-Pot Caliper): Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (for 2-Pot Caliper)>INSPECTION

for Front Brake (except 2-Pot Caliper): Click hereBrake>BRAKE (FRONT)>FRONT BRAKE (except 2-Pot Caliper)>INSPECTION

for Rear Brake: Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSPECTION




Result:
Proceed to
OK
NG



OK

6.RECONFIRM DTC

NG

REPLACE BRAKE DISC

6.RECONFIRM DTC
a.

Reconnect the A41 brake pedal stroke sensor assembly connector.



c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1202 is not output. A
DTC C1202 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster)>PROBLEM SYMPTOMS TABLE




A

B

7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.
C213271C13
1.542,1.854 0.875,2.885 false 2,1.896 2.656,2.927 false 0.781,2.917 1.063,3.198 0.281,0.281 10 E 2.646,2.938 2.885,3.167 0.24,0.229 10 + 0.375,0.354 0.688,0.51 0.313,0.156 10 *a
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Turn the power switch off.


b.

Remove the reservoir filler cap.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the A20 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (+) - 2 (E) Brake fluid level warning switch off (float up) 1.84 to 2.16 kΩ
1 (+) - 2 (E) Brake fluid level warning switch on (float down) Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-36 (LBL) - A20-1 (+) Always Below 1 Ω
A42-36 (LBL) or A20-1 (+) - Body ground Always 10 kΩ or higher
A20-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SWITCH INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SWITCH INPUT)
a.
C156573C27
0.427,1.083 0.813,1.333 0.385,0.25 1.573,2.271 1.083,2.813 false 0.5,1.125 1.094,1.469 0.594,0.344 10 false A20 1,2.833 1.188,3.063 0.188,0.229 10 false + 0.333,0.344 0.646,0.5 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Reconnect the A42 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A20-1 (+) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK BRAKE DISC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY