Home › Drivetrain › K120 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0372181 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K120 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P07457F  Pressure Control Solenoid "A" Actuator Stuck Off  


DESCRIPTION

Using the current from the TCM, the shift solenoid valve SL1 controls the C1 clutch pressure in accordance with the requested shift mode.

When the TCM requests the shift mode to be changed to gear mode, the C1 clutch is engaged and the input torque is transmitted to the 1st gear via the forward clutch drum.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P07457F Pressure Control Solenoid "A" Actuator Stuck Off Any of the following conditions are met (2-trip detection logic):
·

When the TCM commands the C1 clutch to be engaged, the difference between the signals from the transmission revolution sensor (NT) and (NC1) is more than 200 rpm for 1 second or more.

·

The time between when the TCM commands the C1 clutch to be engaged and when the C1 clutch is actually engaged is less than 0.2 seconds.


·

Transmission valve body assembly (shift solenoid valve SL1)

·

Continuously variable transaxle assembly


Comes on DTC stored SAE Code:
P0746

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition TCM commands the C1 clutch to be engaged ○ ○
Malfunction Condition Difference between the signals from the transmission revolution sensor (NT) and (NC1) is more than 200 rpm ○ -
The time between when the TCM commands the C1 clutch to be engaged and when the C1 clutch is actually engaged is less than 0.2 seconds - ○
Duration 1 second or more -
Detection Logic 2-trip detection logic 2-trip detection logic

HINT:

This DTC is stored when any of the above detection patterns is met.


MONITOR DESCRIPTION

When the TCM requests the shift mode to be changed to gear mode, the shift solenoid valve SL1 is turned ON and the C1 clutch is engaged. As a result, the transmission revolution sensor (NT) signal becomes equal to the transmission revolution sensor (NC1) signal.

By comparing the signals indicating the input shaft revolution (speed) and intermediate shaft (C1 clutch) revolution (speed), the TCM judges if the shift mode is gear mode or not.

When the TCM requests the shift mode to be changed to gear mode, if the difference between the transmission revolution sensor (NT) and (NC1) signals is more than 200 rpm, it determines that the shift solenoid valve SL1 is malfunctioning, illuminates the MIL and stores this DTC.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Perform the D Position Test inspection in Road Test.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

10.

Input the DTC: P07457F.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

If any DTCs other than P07457F are output, perform troubleshooting for those DTCs first.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P07457F)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

e.

Read the DTCs using the GTS.

HINT:
·

If DTC P074512 or P074514 is output, perform troubleshooting for that DTC first.

·

If DTCs P074512 and P074514 are not output but DTC P281F00 is output, perform troubleshooting for DTC P281F00 first.

·

If DTCs P074512, P074514 and P281F00 are not output but DTC P07757F is output, perform troubleshooting for DTC P07757F first.




Result:
Result Proceed to
Only DTC P07457F is output A
DTC P07457F and P074512 are output B
DTC P07457F and P074514 are output C
DTC P07457F and P281F00 are output D
DTC P07457F and P07757F are output E
DTC P07457F and DTCs other than P074512, P074514, P07757F and P281F00 are output F



A

2.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL1)

B

C

D

E

F

2.INSPECT TRANSMISSION VALVE BODY ASSEMBLY (SHIFT SOLENOID VALVE SL1)
a.

Disconnect the transmission wire connector from the shift solenoid valve SL1.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL

C398704C01
2.979,1.104 3.563,1.104 true 4.833,1.25 5.25,1.583 true 5.5,1.583 5.917,1.25 true 1.188,0.167 1.5,0.323 0.313,0.156 10 false *1 3.615,1.031 3.927,1.188 0.313,0.156 10 false *2 4.583,0.76 4.896,0.917 0.313,0.156 10 false *a 4.719,1.177 4.875,1.375 0.156,0.198 10 false 2 5.969,1.167 6.125,1.365 0.156,0.198 10 false 1 5.563,2.385 6.021,2.583 0.458,0.198 10 false (+) 5.052,2.385 5.51,2.583 0.458,0.198 10 false (-)
*1 Transmission Valve Body Assembly *2 Shift Solenoid Valve SL1
*a Component without harness connected
(Shift Solenoid Valve SL1)
- -



b.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve SL1 connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

3.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NG

4.REPLACE TRANSMISSION VALVE BODY ASSEMBLY
3.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.REPLACE TRANSMISSION VALVE BODY ASSEMBLY
a.

Replace the transmission valve body assembly.

Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT