This DTC is stored when the multiplex network door ECU detects a malfunction of the motor built-into the power back door unit assembly set LH or power back door unit assembly set RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2220 | Back Door Motor Circuit | Malfunction of motor built into the power back door unit assembly set LH or power back door unit assembly set RH detected | ·
Multiplex network door ECU ·
Power back door unit assembly set LH ·
Power back door unit assembly set RH ·
Harness or connector |
If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors has been disconnected, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION
Clear the DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR
DTC B2220 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Fully open the back door.
| *a | Component without harness connected
(Power Back Door Unit Assembly Set LH) |
Disconnect the power back door unit assembly set LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (BD+) - Body ground | Always | 10 kΩ or higher |
| 2 (BD-) - Body ground | Always | 10 kΩ or higher |
| 1 (BD+) - 2 (BD-) | Always | Below 1 MΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Fully open the back door.
| *a | Component without harness connected
(Power Back Door Unit Assembly Set RH) |
Disconnect the power back door unit assembly set RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (BD+2) - Body ground | Always | 10 kΩ or higher |
| 2 (BD-2) - Body ground | Always | 10 kΩ or higher |
| 1 (BD+2) - 2 (BD-2) | Always | Below 1 MΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R19 multiplex network door ECU connector.
Disconnect the R21 power back door unit assembly set LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R19-7 (BD+) - R21-1 (BD+) | Always | Below 1 Ω |
| R19-6 (BD-) - R21-2 (BD-) | Always | Below 1 Ω |
| R19-7 (BD+) or R21-1 (BD+) - Body ground | Always | 10 kΩ or higher |
| R19-6 (BD-) or R21-2 (BD-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the R19 multiplex network door ECU connector.
Disconnect the R20 power back door unit assembly set RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R19-8 (BD+2) - R20-1 (BD+2) | Always | Below 1 Ω |
| R19-9 (BD-2) - R20-2 (BD-2) | Always | Below 1 Ω |
| R19-8 (BD+2) or R20-1 (BD+2) - Body ground | Always | 10 kΩ or higher |
| R19-9 (BD-2) or R20-2 (BD-2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG