Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM (for Gasoline Model)
RM3620E _59 Vehicle Exterior _076335 DOOR / HATCH _0376805 POWER BACK DOOR SYSTEM(for Gasoline Model) C

DOOR / HATCH  POWER BACK DOOR SYSTEM(for Gasoline Model)  B2226  PBD Unit Pulse Sensor LH Circuit  


DESCRIPTION

This DTC is output when the multiplex network door ECU detects a power back door unit assembly set LH pulse malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2226 PBD Unit Pulse Sensor LH Circuit Multiplex network door ECU detects power back door unit assembly set LH pulse malfunction
·

Multiplex network door ECU

·

Power back door unit assembly set LH

·

Harness or connector



WIRING DIAGRAM

E357347E58
4.073,2.625 4.531,2.823 0.458,0.198 10 false R18 4.094,2.802 5.969,3.094 1.875,0.292 10 false Multiplex Network Door ECU 4.333,2.302 4.792,2.5 0.458,0.198 10 false DSG 4.323,1.792 4.781,1.99 0.458,0.198 10 false DSV 4.344,1.281 4.802,1.479 0.458,0.198 10 false DS2 4.333,0.76 4.792,0.958 0.458,0.198 10 false DS1 2.115,0.635 2.573,0.833 0.458,0.198 10 false DS1 2.125,1.167 2.583,1.365 0.458,0.198 10 false DS2 2.094,1.688 2.552,1.885 0.458,0.198 10 false DSV 2.083,2.188 2.542,2.385 0.458,0.198 10 false DSG 4.938,0.885 5.396,1.083 0.458,0.198 10 false CPU 5.104,1.448 5.563,1.646 0.458,0.198 10 false +B 4.104,0.51 4.26,0.708 0.156,0.198 10 false 1 4.104,1.021 4.26,1.219 0.156,0.198 10 false 2 2.51,1.542 2.667,1.74 0.156,0.198 10 false 3 2.521,2.063 2.677,2.26 0.156,0.198 10 false 4 2.51,0.521 2.667,0.719 0.156,0.198 10 false 5 2.51,1.021 2.667,1.219 0.156,0.198 10 false 6 4.052,1.542 4.365,1.74 0.313,0.198 10 false 25 4.052,2.063 4.365,2.26 0.313,0.198 10 false 21 1.292,2.646 1.75,2.844 0.458,0.198 10 false R21 1.313,2.813 2.698,3.156 1.385,0.344 10 false Power Back Door Unit Assembly Set LH

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

b.

Check for DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Back Door > Trouble Codes
50001 159
OK:

DTC B2226 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - POWER BACK DOOR UNIT ASSEMBLY SET LH)
a.

Disconnect the R18 multiplex network door ECU connector.


b.

Disconnect the R21 power back door unit assembly set LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R18-21 (DSG) - R21-4 (DSG) Always Below 1 Ω
R18-25 (DSV) - R21-3 (DSV) Always Below 1 Ω
R18-2 (DS2) - R21-6 (DS2) Always Below 1 Ω
R18-1 (DS1) - R21-5 (DS1) Always Below 1 Ω
R18-21 (DSG) or R21-4 (DSG) - Body ground Always 10 kΩ or higher
R18-25 (DSV) or R21-3 (DSV) - Body ground Always 10 kΩ or higher
R18-2 (DS2) or R21-6 (DS2) - Body ground Always 10 kΩ or higher
R18-1 (DS1) or R21-5 (DS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MULTIPLEX NETWORK DOOR ECU
a.
E356834C45
0.146,0.927 0.51,1.281 0.365,0.354 1.927,1.135 2.229,0.74 2.229,0.74 2.375,0.74 true 1.896,1.458 2.094,1.781 2.094,1.781 2.26,1.781 true 1.063,0.708 1.219,0.708 1.219,0.708 1.635,1.208 true 1.26,1.813 1.438,1.813 1.438,1.813 1.688,1.427 true 0.135,0.083 0.594,0.281 0.458,0.198 10 false *a 0.198,1.052 0.656,1.25 0.458,0.198 10 false R21 0.75,0.625 1.208,0.823 0.458,0.198 10 false DSG 2.344,1.698 2.802,1.896 0.458,0.198 10 false DS1 0.958,1.729 1.417,1.927 0.458,0.198 10 false DS2 2.458,0.667 2.917,0.865 0.458,0.198 10 false DSV
*a Front view of wire harness connector
(to Power Back Door Unit Assembly Set LH)


Disconnect the power back door unit assembly set LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R21-4 (DSG) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R21-5 (DS1) - Body ground Always 7 V or higher
R21-6 (DS2) - Body ground Always 7 V or higher
R21-3 (DSV) - Body ground Always 7 V or higher



Result:
Proceed to
OK
NG



OK

4.CHECK POWER BACK DOOR UNIT ASSEMBLY SET LH

NG

REPLACE MULTIPLEX NETWORK DOOR ECU

4.CHECK POWER BACK DOOR UNIT ASSEMBLY SET LH
a.

Using an oscilloscope, check the waveform of each terminal from the rear of the multiplex network door ECU R18 connector.

E356836C34
0.885,0.688 1.292,0.948 0.406,0.26 1.792,1.49 1.865,2.115 true 1.729,1.49 1.333,2.188 true 4.292,2.073 4.75,2.271 0.458,0.198 10 false GND 6.813,2.083 7.156,2.333 0.344,0.25 10 false GND 0.083,0.073 0.542,0.271 0.458,0.198 10 false *a 0.979,0.75 1.438,0.948 0.458,0.198 10 false R18 1.229,2.25 1.688,2.448 0.458,0.198 10 false DS2 1.729,2.167 2.188,2.365 0.458,0.198 10 false DS1 2.125,0.563 2.583,0.76 0.458,0.198 10 false *b 4.698,0.542 5.156,0.74 0.458,0.198 10 false *c
*a Component with harness connected
(Multiplex Network Door ECU)
*b Waveform (CH1)
*c Waveform (CH2) - -


Measurement Condition:
Item Condition
Tester Connection
·

CH1 : R18-1 (DS1) - Body ground

·

CH2 : R18-2 (DS2) - Body ground


Tool setting 2 V/DIV., 2 ms./DIV.
Vehicle condition Open and close the back door by hand.


HINT:

The period changes in accordance to the speed at which the back door is opened and closed by hand.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPLACE POWER BACK DOOR UNIT ASSEMBLY SET LH