The kick door control sensor receives vehicle speed, IG and ACC signals from the main body ECU (multiplex network body ECU) via LIN communication and uses the information to stop sensor oscillation.
When the kick door control sensor detects a kick operation, it sends an operation signal to the multiplex network door ECU.
Before troubleshooting, make sure that the "Kick Sensor Function" customize setting is set to "ON" (The default is "ON").
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>CUSTOMIZE PARAMETERS
Before troubleshooting, be sure to read Precautions for Hands Free Power Back Door.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>PRECAUTION
If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors has been disconnected, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>INITIALIZATION
After performing work, using the GTS, read the Data List item "Kick Sensor Connection" and check that the kick door control sensor is connected.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR
DTC is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Kick Sensor Error | Status of the kick door control sensor error | Normal or Error | Normal: Kick door control sensor is normal
Error: Kick door control sensor is abnormal |
- |
| Tester Display |
|---|
| Kick Sensor Error |
On the GTS, Normal is displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Kick Sensor Detection | Status of the kick door control sensor detection | OFF or ON | OFF: Kick door control sensor not detecting a foot
ON: Kick door control sensor detecting a foot |
- |
| Tester Display |
|---|
| Kick Sensor Detection |
On GTS screen, item changes between ON and OFF according to above chart.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Q7 kick door control sensor connector.
Disconnect the 4D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q7-6 (LIN) - 4D-17 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Kick Door Control Sensor) |
Disconnect the kick door control sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q7-7 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q7-2 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Q7 kick door control sensor connector.
Disconnect the R18 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q7-3 (KSOT) - R18-14 (KSIN) | Always | Below 1 Ω |
| Q7-3 (KSOT) or R18-14 (KSIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the multiplex network door ECU with the connector(s) still connected.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER ECU>REMOVAL
| *a | Component with harness connected
(Multiplex Network Door ECU) |
| *b | Waveform |
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tester Connection | R18-14 (KSIN) - Body ground |
| Tool Setting | 2 V/DIV., 50 ms./DIV. |
| Vehicle Condition | Engine switch on (IG), kick door control sensor not detecting a foot |
The waveform displayed is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG