Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory) › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076405 SEAT _0374972 FRONT POWER SEAT CONTROL SYSTEM(for HV Model with Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(for HV Model with Memory)  Power Seat does not Return to Memorized Position  


DESCRIPTION

When the M1 or M2 switch of the seat memory switch is pressed, the main body ECU (multiplex network body ECU) sends a recall request signal to the position control ECU assembly (driver seat). The position control ECU assembly (driver seat) operates each motor to move the seat to the memorized position.

WIRING DIAGRAM

B531534E04
0.104,1.198 2.052,1.615 1.948,0.417 10 false Position Control ECU Assembly (Driver Seat) 3.104,2.844 4.74,3.229 1.635,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 0.688,3.458 2.458,3.677 1.771,0.219 10 false : CAN Communication Line 4.396,0.458 4.875,0.729 0.479,0.271 10 false M1 4.719,1.667 5.198,1.938 0.479,0.271 10 false 7 4.719,1.01 5.198,1.281 0.479,0.271 10 false 9 4.698,0.344 5.177,0.615 0.479,0.271 10 false 10 5.354,2.26 5.833,2.531 0.479,0.271 10 false 1 5.552,2.26 6.031,2.531 0.479,0.271 10 false E 5.521,2.969 6.833,3.385 1.313,0.417 10 false Seat Memory Switch (Driver Door) 4.375,1.115 4.854,1.385 0.479,0.271 10 false M2 4.344,1.771 4.823,2.042 0.479,0.271 10 false MM 5.344,0.344 5.823,0.615 0.479,0.271 10 false 3 5.354,1 5.833,1.271 0.479,0.271 10 false 4 5.354,1.667 5.833,1.938 0.479,0.271 10 false 2 5.542,0.865 5.833,1.031 0.292,0.167 10 false 2*1 5.521,1.51 6.094,1.677 0.573,0.167 10 false MMRY*1 3.115,2.646 3.458,2.854 0.344,0.208 10 false G43 5.521,2.813 6.5,3.083 0.979,0.271 10 false J4*1, I5*2 3.792,3.5 5.479,3.698 1.688,0.198 10 false *1: for LHD 4.75,3.479 6.438,3.677 1.688,0.198 10 false *2: for RHD 5.531,0.25 5.833,0.417 0.302,0.167 10 false 1*1 5.521,0.385 5.896,0.542 0.375,0.156 10 false M1*2 5.531,1.021 5.906,1.177 0.375,0.156 10 false M2*2 5.521,1.677 6.063,1.854 0.542,0.177 10 false MRY*2



CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a restoring operation has failed, release all of the switches. The seat memory restoring function will not operate unless the switches are released.

·

The front power seat control system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to the Service Bulletin.

·

The vehicle auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Initializing the position control ECU assembly (driver seat) will clear the seat position memory.



HINT:

Make sure to initialize the position control ECU assembly (driver seat) after replacing the seat assembly or any related parts (including removal and installation).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>REGISTRATION


PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch (driver seat).

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the front power seat switch (driver seat).



Result:
Proceed to
OK
NG



OK

2.CHECK SEAT POSITION MEMORY FUNCTION

NG

2.CHECK SEAT POSITION MEMORY FUNCTION
a.

Check the seat position memory function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>OPERATION CHECK

OK:

Seat position memory function is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION RESTORING FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

3.CHECK SEAT POSITION RESTORING FUNCTION
a.

Under each of the following conditions, check that the seat position restoring function operates by pressing the M1 or M2 switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>OPERATION CHECK

·

The power switch is on (IG), and the shift lever is in P.*1

·

Within 180 seconds after the driver door is opened with the power switch off.*2

·

Within 60 seconds after the driver door is opened and then closed with the power switch off.*3



Result:
Result Proceed to
Seat position restoring function does not operate at all. A
Seat position restoring function does not operate when the condition is *1. B
·

Seat position restoring function does not operate when the condition is *2.

·

Seat position restoring function does not operate when the condition is *3.


C



A

4.READ VALUE USING GTS (SEAT POSITION MEMORY)

B

7.READ VALUE USING GTS (SHIFT P POSITION STATE)

C

10.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
4.READ VALUE USING GTS (SEAT POSITION MEMORY)
a.

Store a seat position in memory for the M1 and M2 switches.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>OPERATION CHECK


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Driver Seat / Data List.


f.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Seat Memory No1
Seat Memory No2
50003 162 3,4
OK:

Mem is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

5.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

5.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)
a.

Replace the position control ECU assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
6.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] WAS DEFECTIVE)

NG

7.READ VALUE USING GTS (SHIFT P POSITION STATE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position Current shift state P / R / N / D / B Matches currently selected shift state:
P, R, N, D
-
Powertrain > Hybrid Control > Data List
Tester Display
Shift Position
50003 397 231
OK:

On the GTS screen, the current shift state is displayed accordingly.



Result:
Proceed to
OK
NG



OK

8.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

8.REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)
a.

Replace the position control ECU assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
9.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (for HV Model with Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY [DRIVER SEAT] WAS DEFECTIVE)

NG

10.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*1 ON or OFF ON: Driver door open
OFF: Driver door closed
-
FL Door Courtesy SW Front door courtesy light switch assembly (driver door) signal*2 ON or OFF ON: Driver door open
OFF: Driver door closed
-

*1: for RHD

*2: for LHD


Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)