The main body ECU (multiplex network body ECU) detects the condition of the courtesy light switch.
w/ Entry and Start System:
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Read the Data List according to the display on the GTS.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Door Courtesy SW | Rear door courtesy light switch assembly RH signal | OFF or ON | OFF: Rear door RH closed
ON: Rear door RH open |
- |
| RL Door Courtesy SW | Rear door courtesy light switch assembly LH signal | OFF or ON | OFF: Rear door LH closed
ON: Rear door LH open |
- |
| FR Door Courtesy SW | Front door courtesy light switch assembly RH signal | OFF or ON | OFF: Front door RH closed
ON: Front door RH open |
- |
| FL Door Courtesy SW | Front door courtesy light switch assembly LH signal | OFF or ON | OFF: Front door LH closed
ON: Front door LH open |
- |
| Tester Display |
|---|
| RR Door Courtesy SW |
| RL Door Courtesy SW |
| FR Door Courtesy SW |
| FL Door Courtesy SW |
Normal conditions listed above are displayed.
| Result | Proceed to |
|---|---|
| OK | A |
| NG ("FR Door Courtesy SW" is abnormal) | B |
| NG ("FL Door Courtesy SW" is abnormal) | C |
| NG ("RR Door Courtesy SW" is abnormal) | D |
| NG ("RL Door Courtesy SW" is abnormal) | E |
A
B
C
D
E
Remove the front door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M4 front door courtesy light switch assembly RH connector.
Disconnect the G44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M4-1 - G44-6 (FRCY) | Always | Below 1 Ω |
| M4-1 or G44-6 (FRCY) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Remove the front door courtesy light switch assembly LH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly LH.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N7 front door courtesy light switch assembly LH connector.
Disconnect the G44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N7-1 - G44-1 (FLCY) | Always | Below 1 Ω |
| N7-1 or G44-1 (FLCY) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Remove the rear door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL
Inspect the rear door courtesy light switch assembly RH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M5 rear door courtesy light switch assembly RH connector.
Disconnect the 4A instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-1 - 4A-31 | Always | Below 1 Ω |
| M5-1 or 4A-31 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4A-31 - A-2 (RCTY) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D
Remove the rear door courtesy light switch assembly LH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL
Inspect the rear door courtesy light switch assembly LH.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N8 rear door courtesy light switch assembly LH connector.
Disconnect the 4N*1 or 4H*2 instrument panel junction block assembly connector.
*1: for LHD, Manual Transaxle
*2: except LHD, Manual Transaxle
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N8-1 - 4N-24 | Always | Below 1 Ω |
| N8-1 or 4N-24 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N8-1 - 4H-24 | Always | Below 1 Ω |
| N8-1 or 4H-24 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *A | for LHD, Manual Transaxle | *B | except LHD, Manual Transaxle |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4N-24 - A-13 (LCTY) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4H-24 - A-13 (LCTY) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D