Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0374955 HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY)  P0ABF28  Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure  


DESCRIPTION

Refer to the description for DTC P0ABF11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>P0ABF11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure The offset value of the battery current sensor is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

HV battery junction block assembly

·

Hybrid battery thermistor


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0ABF28
·

Hybrid Battery Current for Hybrid Battery Control *1

·

Hybrid Battery Current



HINT:

*1: The value of "Hybrid Battery Current for Hybrid Battery Control" usually changes by 4 A or more while the vehicle is accelerating and decelerating.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Drive the vehicle on urban roads for approximately 10 minutes.

6.

Turn the power switch off and wait for 2 minutes or more.

7.

Turn the power switch on (IG) and turn the GTS on.

8.

With power switch on (IG) and wait for 10 seconds or more.

9.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
"P0AFC00, P0AFC96 or P0A9563" is not output. A
"P0AFC00, P0AFC96 or P0A9563" is also output. B


e.

Turn the power switch off.



A

2.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

OK

3.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))

NG

3.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
C408110C09
1.677,0.208 2.115,0.438 0.438,0.229 1.135,1.667 1.677,0.979 true 1.688,0.875 1.26,0.427 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.802,0.24 2.198,0.552 0.396,0.313 10 false z19 0.938,1.708 1.271,1.969 0.333,0.26 10 false GIB 0.958,0.344 1.292,0.604 0.333,0.26 10 false VIB
*a Component with harness connected
(Battery Voltage Sensor)


Using a Toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z19-6 (VIB) - z19-12 (GIB) Power switch on (IG)

NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Be sure to set the Toyota electrical tester to 40 V when performing this test.




f.
C408110C10
1.635,0.177 2.073,0.406 0.438,0.229 1.135,1.667 1.677,0.979 true 1.76,0.865 1.188,0.365 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.719,0.198 2.115,0.51 0.396,0.313 10 false z19 0.99,1.688 1.323,1.948 0.333,0.26 10 false GIB 0.969,0.271 1.406,0.625 0.438,0.354 10 false IB0
*a Component with harness connected
(Battery Voltage Sensor)


Using a Toyota electrical tester set to 4 V, measure the IB0 voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z19-5(IB0) - z19-12(GIB) Power switch on (IG)

NOTICE:

Be sure to set the Toyota electrical tester to 4 V when performing this test.



g.

Compare the measured values of the IB0 terminal voltage and VIB terminal voltage using the following formula:

IB0 voltage - VIB Voltage / 2 = less than 0.081 V
IB0 voltage - VIB Voltage / 2 = -0.081 V or higher


Result:
Result Proceed to
Within the specified range above A
Other than above B


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Install the No. 1 hybrid battery exhaust duct.


HINT:

When the power switch is on (IG), the actual current will be approximately 0 A. The following graph shows the relation between the actual output voltage of the battery current sensor terminal IB0 and the actual current used for DTC judgment.

A382906E03
1.708,0.281 2.625,0.729 0.917,0.448 10 false Voltage 4.844,2.188 5.865,2.698 1.021,0.51 10 false Current 1.583,1.219 2.5,1.667 0.917,0.448 10 false VIB/2 3.177,2.656 4.094,3.104 0.917,0.448 10 false -4 A 3.896,2.656 4.813,3.115 0.917,0.458 10 false +4 A 3.563,2.656 4.479,3.104 0.917,0.448 10 false 0 A 0.625,2.813 3.615,3.052 2.99,0.24 10 false Battery Current Sensor Normal Range 0.615,3.073 3.604,3.313 2.99,0.24 10 false Toyota electrical tester margin of error 0.625,3.344 3.635,3.646 3.01,0.302 10 false Battery current sensor operation malfunction



A

4.REPLACE BATTERY VOLTAGE SENSOR

B

4.REPLACE BATTERY VOLTAGE SENSOR

NEXT

5.SIMULATION TEST
5.SIMULATION TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Drive the vehicle on urban roads for approximately 10 minutes.


f.

Turn the power switch off and wait for 2 minutes or more.


g.

Turn the power switch on (IG) and wait for 10 seconds or more.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
6.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read output DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

e.

Turn the power switch off.


Result:
Result Proceed to
P0ABF28 is not output. A
P0ABF28 is output. B



A

COMPLETED

B