Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0374955 HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY)  P0ADD11  Hybrid/EV Battery Negative Contactor Circuit Short to Ground  


DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>P0AE411

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground Short to ground in the SMRG circuit:
Primary circuit of SMR (-) is malfunctioning.
(2 trip detection logic)
·

Wire harness or connector

·

HV battery junction block assembly

·

Hybrid vehicle control ECU assembly


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0ADD11
·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Hybrid Battery Voltage

·

SMRP Status

·

SMRB Status

·

SMRG Status

·

SMRP Control Status

·

SMRB Control Status

·

SMRG Control Status

·

Boosting Converter Shutdown Status

·

Generator Inverter Shutdown Status

·

Motor Inverter Shutdown Status



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (READY) and wait for 30 seconds or more.

6.

Turn the power switch off and wait for 2 minutes or more.

7.

Turn the power switch on (IG) and turn the GTS on.

8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

If DTC P0ADD11 is output, the power switch cannot be turned on (READY).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD



b.
C411164C06
1.531,0.146 1.99,0.396 0.458,0.25 0.844,1.281 0.667,1.875 true 0.396,0.177 0.708,0.333 0.313,0.156 10 false *a 1.625,0.188 1.969,0.375 0.344,0.188 10 false A31 0.469,1.896 0.948,2.094 0.479,0.198 10 false SMRG 0.146,0.073 0.458,0.229 0.313,0.156 10 false *A
*A for LHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-13 (SMRG) - Body ground Power switch off 25.0 to 59.0 Ω



c.
C411164C07
1.5,0.156 1.885,0.406 0.385,0.25 0.615,1.823 0.833,1.292 true 1.552,0.208 2.01,0.406 0.458,0.198 10 false G64 0.135,0.094 0.448,0.292 0.313,0.198 10 false *A 0.375,0.219 0.688,0.417 0.313,0.198 10 false *a 0.406,1.885 1.021,2.083 0.615,0.198 10 false SMRG
*A for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G64-13 (SMRG) - Body ground Power switch off 25.0 to 59.0 Ω



d.

Reconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

2.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.




c.
A405664N18
1.313,1.281 1.729,1.552 0.417,0.271 1.333,1.302 1.698,1.521 0.365,0.219 10 true M32

Disconnect the M32 HV battery junction block assembly connector.


d.

Disconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD



e.
C404104C14
2.604,3.333 3.073,3.604 0.469,0.271 1.406,0.167 1.875,0.438 0.469,0.271 2.021,3.406 2.042,3.917 true 0.781,1.344 0.698,1.938 true 0.323,0.25 0.635,0.406 0.313,0.156 10 false *a 0.417,2.479 0.729,2.635 0.313,0.156 10 false *b 1.531,0.219 1.865,0.396 0.333,0.177 10 false A31 2.719,3.385 3.052,3.563 0.333,0.177 10 false M32 0.49,1.99 1.104,2.188 0.615,0.198 10 false SMRG 1.927,3.979 2.542,4.177 0.615,0.198 10 false SMRG 0.125,0.083 0.438,0.24 0.313,0.156 10 false *A
*A for LHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-13 (SMRG) or M32-4 (SMRG) - Body ground and other terminals Power switch off 10 kΩ or higher



f.
C404104C15
2.604,3.333 3.073,3.604 0.469,0.271 1.406,0.167 1.875,0.438 0.469,0.271 2.021,3.406 2.042,3.917 true 0.781,1.344 0.698,1.938 true 0.375,0.24 0.688,0.396 0.313,0.156 10 false *a 0.531,2.5 0.844,2.656 0.313,0.156 10 false *b 1.531,0.219 1.865,0.396 0.333,0.177 10 false G64 2.719,3.385 3.052,3.563 0.333,0.177 10 false M32 0.49,1.99 1.104,2.188 0.615,0.198 10 false SMRG 1.927,3.979 2.542,4.177 0.615,0.198 10 false SMRG 0.115,0.094 0.427,0.25 0.313,0.156 10 false *A
*A for RHD
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU Assembly)
*b Front view of wire harness connector
(to HV Battery Junction Block Assembly)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G64-13 (SMRG) or M32-4 (SMRG) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Reconnect the A31*1, G64*2 hybrid vehicle control ECU assembly connector.

*1: for LHD

*2: for RHD



h.

Reconnect the M32 HV battery junction block assembly connector.


i.

Install the No. 1 HV battery cover panel RH.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR