Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0374955 HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY) C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 2WD with NICKEL METAL HYDRIDE BATTERY)  P30004B  Hybrid/EV Battery Control System Over Temperature  


DESCRIPTION

The hybrid vehicle control ECU assembly monitors its internal operation and detects the following malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P30004B Hybrid/EV Battery Control System Over Temperature The HV battery temperature becomes too high due to a malfunction in the HV system.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid vehicle control ECU assembly

·

HV battery


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P30004B
·

Hybrid Battery Temperature 1 to 3

·

Hybrid Battery Cooling Fan Intake Air Temperature 1

·

Ambient Temperature

·

Hybrid Battery Current

·

Hybrid Battery SOC

·

Hybrid Battery Cooling Fan 1 Drive Status

·

Hybrid Battery Cooling Fan



CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Hybrid Battery Temperature 1 to 3", "Hybrid Battery Cooling Fan Intake Air Temperature 1", "Ambient Temperature" and "Hybrid Battery Current".

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 2WD with NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection.

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P30004B only is output. A
DTCs other than P30004B are also output. B



e.

Turn the power switch off.



A

2.CLEAN NO. 1 HV BATTERY INTAKE FILTER

B

2.CLEAN NO. 1 HV BATTERY INTAKE FILTER
a.
C404111C01
2.063,1.281 2.49,1.281 true 2.531,1.188 2.771,1.385 0.24,0.198 10 true *a
*a Intake Port


Check the HV battery cooling system intake port for blockage.

HINT:

If anything is blocking the HV battery cooling system intake port, remove it.



b.

Clean the No. 1 HV battery intake filter.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY COOLING FILTER>INSPECTION


Result:
Proceed to
NEXT



NEXT

3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
3.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P30004B.

Powertrain > Hybrid Control > Trouble Codes
50001 397
NOTICE:
A408998C06
0.052,0.042 3.115,0.24 3.063,0.198 10 false Freeze Frame Data Recording Example 0.458,1.344 0.771,1.542 0.313,0.198 10 false *a 1.24,1.375 1.552,1.573 0.313,0.198 10 false *a 2.104,1.365 2.417,1.563 0.313,0.198 10 false *a 2.917,1.365 3.229,1.563 0.313,0.198 10 false *a 2.5,0.417 2.813,0.615 0.313,0.198 10 false *b 2.625,1.865 2.938,2.063 0.313,0.198 10 false *c 2.531,1.469 2.844,1.667 0.313,0.198 10 false *a
*a Freeze Frame Data Recorded
*b DTC Stored
*c Time


Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze frame data recorded before "0s" (when the DTC was stored).


Result:
Result Proceed to
Other than below A
The difference between the value of "VL-Voltage before Boosting" and the total of "Hybrid Battery Block 1 to 11 Voltage" is 10 V or more. B



e.

Turn the power switch off.



A

4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

7.REPLACE BATTERY VOLTAGE SENSOR
4.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P30004B.

Powertrain > Hybrid Control > Trouble Codes
50001 397
NOTICE:

Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze frame data recorded at "0s" (when the DTC was stored).



Result:
Result Proceed to
Other than below A
The value of any of "Hybrid Battery Temperature 1 to 3" is 80°C (176°F) or more. B


e.

Turn the power switch off.



A

5.READ VALUE USING GTS (DATA LIST)

B

8.REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY
5.READ VALUE USING GTS (DATA LIST)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Temperature 1 to 3.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Temperature 1
Hybrid Battery Temperature 2
Hybrid Battery Temperature 3
50003 397 198,199,200

d.

According to the display on the GTS, read the Data List and check that the value of each "Hybrid Battery Temperature 1 to 3" is 40°C (104°F) or less.

HINT:

If the value of any of "Hybrid Battery Temperature 1 to 3" is more than 40°C (104°F), turn the power switch off and wait until the values to decrease to 40°C (104°F) or less before continuing this procedure.



e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1, 2, 9, 10, 11 Voltage.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 1 Voltage
Hybrid Battery Block 2 Voltage
Hybrid Battery Block 9 Voltage
Hybrid Battery Block 10 Voltage
Hybrid Battery Block 11 Voltage
50003 397 161,162,169,170,307

f.

According to the display on the GTS, read the Data List and check the value of each "Hybrid Battery Block 1, 2, 9, 10 and 11 Voltage" with the power switch on (IG).

A412005C04
5.875,1.521 6.052,1.01 6.052,1.01 6.188,1.01 false 1.188,3.333 1.5,3.49 0.313,0.156 10 false *a 1.688,3.344 2,3.5 0.313,0.156 10 false *b 2.208,3.333 2.5,3.583 0.292,0.25 10 false *c 2.667,3.333 2.979,3.49 0.313,0.156 10 false *d 3.167,3.333 3.479,3.49 0.313,0.156 10 false *e 3.667,3.344 3.979,3.5 0.313,0.156 10 false *f 4.083,3.333 4.396,3.552 0.313,0.219 10 false *g 4.583,3.333 4.896,3.49 0.313,0.156 10 false *h 5.104,3.333 5.417,3.49 0.313,0.156 10 false *i 5.583,3.333 5.896,3.49 0.313,0.156 10 false *j 6.188,3.333 6.5,3.49 0.313,0.156 10 false *k 0.031,0.042 3.49,0.427 3.458,0.385 10 false Example for when a difference in the voltage value occurs between the hybrid battery block 2 and 10. 4.208,0.073 6.552,0.458 2.344,0.385 10 false A: Lowest hybrid battery block voltage 4.219,0.521 6.646,1.042 2.427,0.521 10 false B: Highest hybrid battery block voltage 1.729,3.542 1.885,3.74 0.156,0.198 10 false A 5.615,3.531 5.771,3.729 0.156,0.198 10 false B 6.24,0.917 7.156,1.26 0.917,0.344 10 false 0.3 V or more
*a Hybrid Battery Block 1 Voltage *b Hybrid Battery Block 2 Voltage
*c Hybrid Battery Block 3 Voltage *d Hybrid Battery Block 4 Voltage
*e Hybrid Battery Block 5 Voltage *f Hybrid Battery Block 6 Voltage
*g Hybrid Battery Block 7 Voltage *h Hybrid Battery Block 8 Voltage
*i Hybrid Battery Block 9 Voltage *j Hybrid Battery Block 10 Voltage
*k Hybrid Battery Block 11 Voltage - -



Result:
Result Proceed to
Other than below A
The difference between the lowest and highest HV Battery Block Voltage is 0.3 V or more. B


g.

Turn the power switch off.



A

6.READ VALUE USING GTS (DATA LIST)

B

8.REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY
6.READ VALUE USING GTS (DATA LIST)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Temperature 1 to 3.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Temperature 1
Hybrid Battery Temperature 2
Hybrid Battery Temperature 3
50003 397 198,199,200

d.

According to the display on the GTS, read the Data List and check that the value of each "Hybrid Battery Temperature 1 to 3" is 40°C (104°F) or less.

HINT:

If the value of any of "Hybrid Battery Temperature 1 to 3" is more than 40°C (104°F), turn the power switch off and wait until the values to decrease to 40°C (104°F) or less before continuing this procedure.



e.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 3 to 8 Voltage.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid Battery Block 3 Voltage
Hybrid Battery Block 4 Voltage
Hybrid Battery Block 5 Voltage
Hybrid Battery Block 6 Voltage
Hybrid Battery Block 7 Voltage
Hybrid Battery Block 8 Voltage
50003 397 163,164,165,166,167,168

f.

According to the display on the GTS, read the Data List and check the value of each "Hybrid Battery Block 3 to 8 Voltage" with the power switch on (IG).

A412006C05
4.458,1.594 4.719,1.073 4.719,1.073 4.979,1.073 false 1.25,3.344 1.563,3.5 0.313,0.156 10 false *a 1.75,3.344 2.063,3.5 0.313,0.156 10 false *b 2.271,3.333 2.583,3.49 0.313,0.156 10 false *c 2.688,3.344 3,3.5 0.313,0.156 10 false *d 3.167,3.333 3.479,3.49 0.313,0.156 10 false *e 3.667,3.344 3.979,3.5 0.313,0.156 10 false *f 4.083,3.333 4.396,3.656 0.313,0.323 10 false *g 4.771,3.344 5.083,3.5 0.313,0.156 10 false *h 5.271,3.344 5.583,3.5 0.313,0.156 10 false *i 5.771,3.333 6.083,3.49 0.313,0.156 10 false *j 6.271,3.344 6.583,3.5 0.313,0.156 10 false *k 0.042,0.031 3.51,0.406 3.469,0.375 10 false Example for when a difference in the voltage value occurs between the hybrid battery block 4 and 7. 4.542,0.083 6.948,0.49 2.406,0.406 10 false A: Lowest hybrid battery block voltage 4.552,0.51 7.01,0.958 2.458,0.448 10 false B: Highest hybrid battery block voltage 5.031,0.969 5.948,1.365 0.917,0.396 10 false 0.3 V or more 2.719,3.542 2.875,3.74 0.156,0.198 10 false A 4.135,3.552 4.292,3.75 0.156,0.198 10 false B
*a Hybrid Battery Block 1 Voltage *b Hybrid Battery Block 2 Voltage
*c Hybrid Battery Block 3 Voltage *d Hybrid Battery Block 4 Voltage
*e Hybrid Battery Block 5 Voltage *f Hybrid Battery Block 6 Voltage
*g Hybrid Battery Block 7 Voltage *h Hybrid Battery Block 8 Voltage
*i Hybrid Battery Block 9 Voltage *j Hybrid Battery Block 10 Voltage
*k Hybrid Battery Block 11 Voltage - -



Result:
Result Proceed to
Other than below A
The difference between the lowest and highest HV Battery Block Voltage is 0.3 V or more. B


g.

Turn the power switch off.



A

COMPLETED

B

8.REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY