Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBINATION SWITCH › from 2019.02
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0374871 COMBINATION SWITCH G

HEATING / AIR CONDITIONING  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84010D 1.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY


b.

Remove the upper console panel sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>REMOVAL


c.
C407243C05
2.563,1.438 2.563,1.104 true 1.635,0.771 1.635,0.271 1.635,0.271 1.802,0.271 true 1.833,0.188 2.24,0.396 0.406,0.208 10 false ECU 2.417,1.438 2.802,1.667 0.385,0.229 10 false GND 0.198,1.75 0.448,2.021 0.25,0.271 12 false *A 0.125,0.135 0.396,0.365 0.271,0.229 10 false *a 1.885,1.75 2.135,2.021 0.25,0.271 12 false *B
*A for 2WD
*B for 4WD/AWD
*a Component without harness connected
(Integration Control and Panel Assembly (Combination Switch))


for HV Model:

i.

Inspect the ECO mode switch

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 2WD):
Tester Connection Condition Specified Condition
7 (ECU) - 13 (GND) ECO mode switch being pushed and held Below 1 Ω
ECO mode switch not pushed 10 kΩ or higher


Standard Resistance (for 4WD/AWD):
Tester Connection Condition Specified Condition
7 (ECU) - 13 (GND) ECO mode switch being turned and held Below 1 Ω
ECO mode switch not turned 10 kΩ or higher


If the result is not as specified, replace the integration control and panel assembly (combination switch).



d.
C405113C04
2.479,1.615 2.479,1.281 true 1.635,1.021 1.635,0.521 1.635,0.521 1.802,0.521 true 2.344,1.625 2.698,1.854 0.354,0.229 10 false GND 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.833,0.448 2.188,0.677 0.354,0.229 10 false ECU
*a Component without harness connected
(Integration Control and Panel Assembly (Combination Switch))


for Automatic Transaxle and CVT:

i.

Inspect the ECO mode switch

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (ECU) - 13 (GND) ECO mode switch being pushed and held Below 1 Ω
ECO mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the integration control and panel assembly (combination switch).



e.

for Manual Transaxle:

i.
C405125C03
2.052,1.688 2.052,1.354 true 1.375,1.688 1.375,1.354 true 1.917,1.708 2.323,1.958 0.406,0.25 10 false GND 0.083,0.083 0.333,0.333 0.25,0.25 10 false *a 1.24,1.708 1.646,1.958 0.406,0.25 10 false ECU
*a Component without harness connected
(Integration Control and Panel Assembly (Combination Switch))


Inspect the ECO mode switch

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
10 (ECU) - 6 (GND) ECO mode switch being pushed and held Below 1 Ω
ECO mode switch not pushed 10 kΩ or higher


If the result is not as specified, replace the integration control and panel assembly (combination switch).



f.

Install the upper console panel sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX>INSTALLATION